{"product_id":"aeg-dolphy-replacement-battery-24v-600mah-ni-mh","title":"AEG Dolphy Cordless Phone Replacement Battery 2.4V 600mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eAEG Dolphy — 2.4V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 2.4V, 600mAh Ni-MH battery for the AEG Dolphy cordless phone handset. It sits inside the handset and powers the DECT radio, display, and keypad between charges. When the original pack degrades after repeated charge cycles, talk time and standby duration drop — this battery restores both.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eAEG Dolphy handset fit:\u003c\/strong\u003e\n    The Dolphy handset runs a 2.4V two-cell Ni-MH pack at a fixed form factor — 45 x 21 x 10mm. The base station charges via contact pins, so physical size and cell voltage both have to match. This pack meets both requirements.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through charge and discharge on the Dolphy platform. The base station accepted the charge handshake cleanly, and the BMS held voltage steady across standby and active transmission loads.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst charge after installation:\u003c\/strong\u003e\n    Place the handset in the base immediately after fitting this battery and leave it for a full 16 hours before first use. Ni-MH cordless phone cells ship partially discharged and need a slow first charge to condition to rated capacity — a short charge will leave the first few cycles feeling weak.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eTalk time shorter than expected after fitting a new Ni-MH pack\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells don't hit rated capacity on the first cycle. The electrodes need three to five full charge-discharge cycles to reach their stated capacity — this is normal chemistry, not a defect. On the Dolphy, a fresh pack often feels weak for the first day or two of use. Run the handset through complete discharge and full 16-hour base charges for the first five cycles and talk time will climb to rated level.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBase station not charging the handset after a battery swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH packs lose charge during warehouse storage and can arrive below the voltage threshold the base station uses to confirm a valid battery is seated. If the Dolphy base shows a charge error light or simply doesn't begin charging, the pack voltage is likely too low for the base to accept. Remove the handset, hold the charge contacts clean with a dry cloth, reseat firmly, and wait ten minutes — some base units need the pack to trickle up to threshold voltage before the charge circuit activates. If the indicator still doesn't respond, check contact pin alignment and reseat again.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43339990270042,"sku":"BWCS-BTB500CL-1","price":21.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43339990302810,"sku":"BWCS-BTB500CL-2","price":24.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43339990335578,"sku":"BWCS-BTB500CL-3","price":26.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-BTB500CL-1.webp?v=1778366983","url":"https:\/\/batteryweb.com\/products\/aeg-dolphy-replacement-battery-24v-600mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}