{"product_id":"aeg-rapido-replacement-battery-36v-2000mah-ni-mh","title":"AEG Rapido 3.6V Cordless Vacuum Replacement Battery 2000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eAEG Rapido ErgoRapido Series — 3.6V Ni-MH Replacement Battery (405 52 51-393)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.6V Ni-MH replacement battery rated at 2000mAh (7.2Wh) for the AEG Rapido and ErgoRapido cordless handheld vacuums. It fits models ZB5103 and ZB5103W, restoring suction power when the original cell has degraded or failed. Match the OEM part number 405 52 51-393 to confirm fit before ordering.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eRapido and ErgoRapido compatibility:\u003c\/strong\u003e\n    These models share the same 3.6V single-cell NiMH configuration and the same physical connector footprint. The BMS in this cell communicates the same charge termination signal the AEG charger expects — no voltage mismatch or handshake failure at the charging contacts.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge-discharge cycles on the ZB5103 platform. The BMS held the correct delta-V cutoff on charge termination, and the motor current draw remained within rated limits through full discharge on both carpet and hard floor passes.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging on the ErgoRapido:\u003c\/strong\u003e\n    Do not leave the vacuum seated on its wall dock indefinitely between uses. The ErgoRapido dock applies a continuous trickle current when the cell is full. NiMH cells degrade significantly faster under permanent trickle charge — charge to full, then remove the unit from the dock.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator reaches low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe ZB5103 motor draws a surge of current any time it hits resistance — a clump of debris, a dense carpet pile, or a partially blocked filter. On an aged or weakened cell, that current spike pulls the cell voltage below the BMS floor momentarily, reducing motor speed before the gauge shows low charge. The gauge reflects resting voltage, not loaded voltage, so the two readings diverge as the cell ages. A fresh 2000mAh cell at 3.6V handles those brief spikes without the voltage sag that chokes motor speed.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cuts out and recovers during a cleaning pass\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eA cut-out-and-recover pattern on the ErgoRapido is almost always a BMS overcurrent trip, not a faulty motor. When the filter is partially clogged, the motor works harder to maintain airflow, drawing sustained current above the BMS threshold — the BMS trips, the motor stops, the cell voltage recovers, and the motor restarts. Clean the filter first. If the cut-out continues on a clean filter with a new cell, check that the filter mesh is fully seated — a misaligned mesh creates the same restriction. Start by removing and tapping the filter clean before replacing the battery.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43427981394010,"sku":"BWCS-AER393VX-1","price":24.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43427981426778,"sku":"BWCS-AER393VX-2","price":27.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43427981459546,"sku":"BWCS-AER393VX-3","price":30.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-AER393VX-1.webp?v=1779933648","url":"https:\/\/batteryweb.com\/products\/aeg-rapido-replacement-battery-36v-2000mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}