{"product_id":"airrobo-p10-replacement-battery-148v-2600mah-li-ion","title":"Airrobo P10 Replacement Battery 14.8V 2600mAh Li-ion","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eAirrobo P10 — 14.8V Li-ion Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 14.8V, 2600mAh (38.48Wh) lithium-ion battery pack for the Airrobo P10 cordless stick vacuum. It replaces the original pack when capacity has dropped or the battery no longer holds a charge. Fits the P10 motor assembly directly.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eP10 platform fit:\u003c\/strong\u003e\n    The P10 runs a 14.8V four-cell Li-ion configuration. The motor controller is tuned to this voltage rail, and the connector pinout matches the original pack. Swapping voltage or cell count outside spec causes the controller to reject the battery or under-perform.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through full charge and discharge cycles on the P10 motor. The BMS held cutoff correctly at low-cell voltage, and the pack delivered consistent output across hard floor and carpet resistance loads without tripping overcurrent protection.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging habit on the P10:\u003c\/strong\u003e\n    Do not leave the P10 sitting on the charging dock permanently. Continuous trickle charge accelerates capacity fade on Li-ion cells. Charge the pack fully, then remove it from the dock until the next use cycle.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator reaches low on the P10\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens because the P10 motor draws significantly more current when airflow is restricted — a partially blocked filter forces the motor to work harder, pulling the cell voltage down faster than the indicator expects. The indicator reads state of charge under light load, not under the actual motor draw at the time. The result is suction loss well before the battery light signals low. Clean or replace the filter first, then retest — if suction holds longer, the filter was the cause, not the battery.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eP10 motor cuts out mid-clean then restarts after a few seconds\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a dead battery. When suction is blocked — by a clogged filter, a jammed brush roll, or a sealed nozzle — motor current spikes past the BMS threshold and the pack shuts output to protect the cells. After a few seconds the BMS resets and the motor restarts. The fix is to clear the restriction before running again. If the cutout repeats on a clean filter with a new battery, check the brush roll for wrapped fibres and confirm the nozzle pathway is clear.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43428018454618,"sku":"BWCS-PCS780VX-1","price":37.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43428018487386,"sku":"BWCS-PCS780VX-2","price":43.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43428018520154,"sku":"BWCS-PCS780VX-3","price":48.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-PCS780VX-1.webp?v=1779933849","url":"https:\/\/batteryweb.com\/products\/airrobo-p10-replacement-battery-148v-2600mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}