{"product_id":"airrobo-t10-replacement-battery-144v-6700mah-li-ion","title":"Airrobo T10+ Replacement Battery 14.4V 6700mAh Li-ion","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eAirrobo T10+ \/ T9 — 14.4V Li-ion Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 14.4V, 6700mAh (96.48Wh) Li-ion replacement battery for the Airrobo T10+, T10 Plus, and T9 robotic vacuum cleaners. It replaces a degraded or failed original pack and restores full autonomous cleaning operation. Fit the same way as the original — no modifications needed.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eT10+, T10 Plus, and T9 compatibility:\u003c\/strong\u003e\n    All three models share the same 14.4V battery platform, connector format, and BMS communication protocol. Swapping between them carries no compatibility risk — the voltage rail and handshake are identical across the range.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge and discharge cycles on the T10+ dock. The BMS negotiated correctly with the charger, accepted a full charge without fault codes, and held voltage within normal operating range under motor load across repeated runs.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging habit on the T10+:\u003c\/strong\u003e\n    Do not leave the vacuum sitting on the dock continuously between uses. Robotic vacuums on permanent dock charge trickle-charge the cell constantly, which accelerates capacity fade. Charge to full, then remove the unit from the dock until the next cleaning session.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator reaches low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe T10+ motor draws more current when airflow is restricted — a partially blocked filter or full dustbin forces the motor to work harder to maintain suction pressure. That elevated current draw pulls the cell voltage down faster than the indicator expects, so suction weakens while the indicator still shows a healthy charge level. The BMS reads real cell voltage, not a modelled state-of-charge, so the display lags behind the actual power available. Clean the filter and empty the dustbin first — if suction recovers, the battery is not the cause.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cuts out mid-clean then recovers after a few seconds\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a flat battery. When the T10+ drives over thick carpet or encounters a sustained blockage, the motor current spikes beyond the BMS protection threshold and the pack shuts the output temporarily. The BMS resets automatically once the current drops, which is why the vacuum resumes after a short pause. Clear any blockage at the brush roll and check the filter — sustained restriction is the most common trigger. If the cutout repeats on open hard floor with a clean filter, check that cell voltage under load stays above 12.0V.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43427983360090,"sku":"BWCS-BPK120VX-1","price":89.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43427983392858,"sku":"BWCS-BPK120VX-2","price":105.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43427983425626,"sku":"BWCS-BPK120VX-3","price":116.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-BPK120VX-1.webp?v=1779933648","url":"https:\/\/batteryweb.com\/products\/airrobo-t10-replacement-battery-144v-6700mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}