{"product_id":"atlas-copco-loktor-h18-replacement-battery-18v-3000mah-li-ion","title":"Atlas Copco LokTor H18 18V Replacement Battery 3000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eAtlas Copco LokTor H18 \/ P18T \/ P18TX \/ S18P Series — 18V Li-ion Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is an 18V 3000mAh (54Wh) Li-ion battery pack for the Atlas Copco LokTor torque wrench range. It fits the LokTor H18, P18T, P18TX, and S18P, along with eight additional LokTor variants that share the same 18V platform. These are precision cordless torque tools used in automotive assembly lines and industrial fastening — continuous operation matters.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eLokTor platform compatibility:\u003c\/strong\u003e\n    The H18, P18T, P18TX, and S18P share the same 18V battery rail, connector footprint, and BMS communication protocol. One pack works across all of them — no adapters, no firmware mismatch.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through repeated torque-cycle loads on the LokTor platform. The BMS handled motor-start inrush without tripping, held voltage within spec under sustained fastening sequences, and discharged to cutoff cleanly without cell reversal.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eLokTor motor inrush conditioning:\u003c\/strong\u003e\n    On first use, run the tool at half torque for two full cycles before applying maximum torque settings. This lets the BMS profile the motor's inrush current signature and calibrate its overcurrent threshold before you hit peak fastening loads.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBMS overcurrent trip on trigger pull in high-torque fastening\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe LokTor's motor draws a sharp inrush spike the instant the trigger is pulled — especially at maximum torque settings. A new pack with a conservatively set BMS can interpret that spike as a fault and cut power before the fastener even moves. This is not a defective battery. The BMS needs two to three cycles to log the motor's inrush profile and widen its overcurrent window accordingly. If cutoff persists after conditioning cycles, check the battery rail contacts for oxidation — resistance at the contact point amplifies the apparent voltage drop the BMS sees.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCharger shows blinking red and never accepts the new pack\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eA LokTor battery stored in a depleted state can drop below the charger's acceptance voltage threshold — typically under 12V for an 18V Li-ion pack. The charger's protection circuit reads this as a damaged or over-discharged cell and refuses to begin a charge cycle. Most Atlas Copco chargers have a recovery or \"wake\" mode: hold the battery in the charger for 10–15 minutes while the charger trickle-feeds current at a sub-amp rate to bring cells back above the acceptance floor. Once the pack reads above approximately 14V, the charger should switch to normal CC\/CV charge and the indicator will go solid or green.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43416057938010,"sku":"BWCS-MKM180PW-1","price":97.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43416057970778,"sku":"BWCS-MKM180PW-2","price":114.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43416058003546,"sku":"BWCS-MKM180PW-3","price":127.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-MKM180PW-1.webp?v=1779759860","url":"https:\/\/batteryweb.com\/products\/atlas-copco-loktor-h18-replacement-battery-18v-3000mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}