{"product_id":"ats-electro-lube-125cc-ultimate-luber-replacement-battery-6v-2300mah-alkaline","title":"ATS Electro-Lube 125cc Ultimate Luber 6V Alkaline Battery","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eATS Electro-Lube 125cc \/ 60cc Ultimate Luber — 6V Alkaline Replacement Battery (82-90025)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 6V alkaline replacement battery rated at 2300mAh (13.8Wh) for the ATS Electro-Lube Ultimate Luber automated lubrication system. It fits both the 125cc and 60cc Ultimate Luber models. Both units share the same voltage rail, connector format, and cell footprint, so one SKU covers both.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003e125cc and 60cc compatibility:\u003c\/strong\u003e\n    Both Ultimate Luber models run off the same 6V alkaline cell stack. The dispensing motor and timing circuit draw from a common voltage rail, so the battery form factor and discharge profile match across the range without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell against the Ultimate Luber's motor-start cycle, where the dispensing actuator pulls a brief current spike at each lubrication event. The battery held voltage across repeated dispense cycles without triggering a dropout or early cutoff.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eField swap procedure:\u003c\/strong\u003e\n    After fitting a new cell, trigger one manual dispense cycle before returning the unit to its auto-schedule. The timing circuit re-references the voltage baseline on the first actuation — skipping this step can cause the unit to flag a low-battery condition before the schedule even starts.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the Ultimate Luber skips a scheduled dispense cycle after a battery change\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe Ultimate Luber's interval timer uses the battery voltage to anchor its internal reference at startup. A fresh alkaline cell sits above the nominal 6V the circuit was last calibrated against, which can cause the timing logic to misread its position in the dispense cycle. This shows up as one skipped event immediately after installation — not a fault, but a recalibration artefact. One manual trigger resets the reference and the automatic schedule resumes normally from the next interval.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eUnit activates but lubricant output drops noticeably toward end of battery life\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eAlkaline cells under motor load show a gradual voltage taper rather than a flat discharge curve. As the cell drops below approximately 5.4V, the dispensing motor doesn't receive enough voltage to complete a full actuator stroke, so each cycle pushes less lubricant than specified. The unit will still activate and appear functional — the output deficit is only visible if you measure dispense volume directly. Replace the cell when measured output falls short of the rated dispense amount, typically before the low-battery indicator triggers.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43360444088410,"sku":"BWCS-ATE125SL-1","price":38.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43360444121178,"sku":"BWCS-ATE125SL-2","price":45.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43360444153946,"sku":"BWCS-ATE125SL-3","price":49.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-ATE125SL-1.webp?v=1778614683","url":"https:\/\/batteryweb.com\/products\/ats-electro-lube-125cc-ultimate-luber-replacement-battery-6v-2300mah-alkaline","provider":"BatteryWeb","version":"1.0","type":"link"}