{"product_id":"att-9031-replacement-battery-48v-700mah-ni-mh","title":"AT\u0026T 9031 Cordless Phone Compatible Battery 4.8V 700mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eAT\u0026amp;T 9031 Cordless Phone — 4.8V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 4.8V, 700mAh Ni-MH replacement battery for the AT\u0026amp;T 9031 cordless phone handset (also listed as model 700245509). It slots into the handset battery compartment and restores power to the wireless unit. Four cells in series deliver the 4.8V rail the handset needs to operate within range of the base station.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eAT\u0026amp;T 9031 and 700245509 compatibility:\u003c\/strong\u003e\n    Both model numbers reference the same handset platform. They share the same battery compartment dimensions, connector orientation, and 4.8V cell configuration — one battery fits both.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through charge and discharge on the bench. The BMS accepted charge from a standard DECT base station without triggering a fault state, and voltage held stable across the RF transmit cycle.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-charge on NiMH cordless handsets:\u003c\/strong\u003e\n    After installing, seat the handset in the base and leave it for a full 16 hours before first use. NiMH cells in cordless phones need a slow initial charge to reach rated capacity — cutting it short leaves the pack underformed for the first several cycles.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eRange dropping on the AT\u0026amp;T 9031 after a battery swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe 9031 handset adjusts RF transmit power based on available voltage. When a fresh NiMH pack hasn't completed its first conditioning cycles, the resting voltage sags faster under the RF load than a fully conditioned pack would. The base station interprets this as a weak signal and the handset struggles at the edges of its normal range. Run three to five full charge-and-use cycles and the cells will stabilise — voltage sag under transmit load drops noticeably by cycle four.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBase station shows no charge or error light with a new pack installed\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNiMH batteries lose voltage during storage — a pack that's been sitting in a warehouse can drop below 4.0V across the four cells. Some AT\u0026amp;T base stations won't initiate a charge cycle if the incoming voltage is too low, because the charger circuit reads the pack as faulty rather than depleted. To recover it, apply a short trickle charge using a compatible external NiMH charger to bring cell voltage above 1.0V per cell, then reseat the handset in the base. Once the pack reads above roughly 4.2V, the base station charger will accept it and resume normal charging.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43339962024026,"sku":"BWCS-TS9031CL-1","price":24.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43339962056794,"sku":"BWCS-TS9031CL-2","price":27.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43339962089562,"sku":"BWCS-TS9031CL-3","price":30.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-TS9031CL-1.webp?v=1778367002","url":"https:\/\/batteryweb.com\/products\/att-9031-replacement-battery-48v-700mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}