{"product_id":"att-stb-910-replacement-battery-6v-1500mah-ni-mh","title":"AT\u0026T STB-910 Cordless Phone Replacement Battery 6V 1500mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eAT\u0026amp;T STB-910 \/ 24896 \/ 84020 — 6V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 6V, 1500mAh Ni-MH replacement battery for AT\u0026amp;T cordless phone models STB-910, 24896, and 84020. It slots into the handset and restores cordless operation when the original cell can no longer hold a charge. Voltage and capacity match the OEM specification exactly.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eSTB-910, 24896, and 84020 compatibility:\u003c\/strong\u003e\n    These three AT\u0026amp;T models share the same 6V battery bay, connector orientation, and NiMH charge acceptance circuit — the base station's trickle charge termination logic is calibrated for this cell voltage, so swapping a mismatched chemistry would confuse the delta-V detection and leave the pack undercharged.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through charge and discharge on the bench. The NiMH cells accepted trickle charge correctly, and the base station's charge indicator responded as expected without fault signals through three full cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-charge protocol for NiMH handsets:\u003c\/strong\u003e\n    Place the handset in the base immediately after installing this battery and leave it for a full 16 hours before first use. NiMH cells shipped in partial-discharge state need a slow, uninterrupted initial charge to reach rated capacity — cutting it short locks in a lower ceiling that short-charges every cycle after.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBase station charge light not activating on a new NiMH pack\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eAT\u0026amp;T base stations on these models use delta-V sensing to detect an active NiMH charge. If the pack voltage is too low after storage, the base may not register a valid cell and the charge light stays dark. This is not a fault in the battery or the base — it is a threshold issue. Seat the handset firmly, wait 10 minutes, then remove and reseat it. If the voltage has risen even slightly from the contact warmth, the base circuit will often re-sample and begin charging. A pack below roughly 4.8V from deep storage may need a brief external top-up to cross the acceptance threshold.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eTalk time shorter than expected after replacement\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNiMH cells do not deliver rated capacity from cycle one — they need three to five full charge-and-use cycles to reach the 1500mAh figure. A handset that feels weaker than the original in the first few days is almost always still conditioning, not defective. Run the handset down to low-battery cutoff, then return it to the base for a full overnight charge, and repeat this three times. By cycle four, capacity should stabilise at or near the rated level.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43339938725978,"sku":"BWCS-BT910CL-1","price":30.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43339938758746,"sku":"BWCS-BT910CL-2","price":35.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43339938791514,"sku":"BWCS-BT910CL-3","price":38.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-BT910CL-1.webp?v=1778366983","url":"https:\/\/batteryweb.com\/products\/att-stb-910-replacement-battery-6v-1500mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}