{"product_id":"autec-fua10-replacement-battery-72v-2000mah-ni-mh","title":"Autec NC0707L Crane Remote Replacement Battery 7.2V 2000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eAutec FUA10 \/ UTX97 \/ CB71.F — 7.2V Ni-MH Replacement Battery (NC0707L)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 7.2V 2000mAh Ni-MH replacement for the Autec NC0707L and MH0707L battery packs. It fits the FUA10 crane remote, UTX97 transmitter, and CB71.F controller. Voltage and cell count match the original spec — the remote powers on and transmits commands without modification.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eFUA10, UTX97, and CB71.F compatibility:\u003c\/strong\u003e\n    These three Autec units share the same 7.2V six-cell NiMH pack format and connector pinout. One battery fits all three because the BMS voltage thresholds and physical form factor are identical across the range.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through full charge cycles and confirmed the BMS accepted charge without fault flags. Solenoid activation during load testing did not cause voltage dropout — the cell capacity held above the remote's low-battery cutoff threshold under repetitive relay cycling.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePre-use charging on crane remotes:\u003c\/strong\u003e\n    Autec crane remotes shipped with a new battery or returned from storage will show low battery immediately — NiMH cells arrive at storage voltage, not full charge. Connect to the Autec charger and complete a full cycle before the first transmission on site.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy Autec crane remotes cut out during solenoid or relay activation\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eWhen the remote triggers a solenoid or contactor, the inrush current spike can briefly drag cell voltage below the BMS cutoff threshold. This causes the remote to drop out mid-command — not a transmitter fault, but a battery capacity issue. A degraded or partially charged pack has higher internal resistance, which amplifies the voltage sag under load. A fresh, fully charged 2000mAh cell keeps voltage above the cutoff even during back-to-back solenoid activations.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eRemote not powering on after months of infrequent use\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNiMH cells discharged below roughly 0.9V per cell during extended storage can trigger BMS lockout — the protection circuit reads the pack as defective and blocks charge input. The remote won't power on even with a charger connected. Connect the Autec charger and leave it for 30 minutes before checking for a charge indicator. If the charger accepts the pack and begins cycling, the cells are recovering; allow the full charge sequence to complete before use.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43360064634970,"sku":"BWCS-ALK707BL-1","price":50.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43360064667738,"sku":"BWCS-ALK707BL-2","price":58.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43360064700506,"sku":"BWCS-ALK707BL-3","price":64.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-ALK707BL-1.webp?v=1778610751","url":"https:\/\/batteryweb.com\/products\/autec-fua10-replacement-battery-72v-2000mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}