{"product_id":"bci-capnocheck-plus-replacement-battery-6v-5000mah-ni-mh","title":"BCI Capnocheck Plus Replacement Battery 6V 5000mAh 58522B1","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eBCI Capnocheck Plus — 6V Ni-MH Replacement Battery (58522B1)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 6V 5000mAh Ni-MH replacement battery for the BCI Capnocheck Plus capnography monitor. It also fits the Sleeo CO2 Monitor, 58450A1 Mini-Torr Plus, and 6004 Blood Pressure Monitor. Use the OEM part number 58522B1 to confirm fitment before ordering.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eCapnocheck Plus platform fitment:\u003c\/strong\u003e\n    These devices share a 6V Ni-MH cell configuration with a common connector and BMS handshake protocol. The battery management system on each model expects the same charge termination signal — negative delta-V — which Ni-MH chemistry delivers at full charge. Swapping chemistry type will cause charge faults.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through charge and discharge on the Capnocheck Plus platform. The BMS accepted the battery without fault codes after the first full charge cycle. Charge termination triggered correctly at capacity, and the monitor reported battery status accurately from cycle two onward.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-swap power-on sequence:\u003c\/strong\u003e\n    After installing this battery, allow the Capnocheck Plus to complete its full power-on self-test without interruption. The device runs a BMS verification step at startup. Cutting power during this sequence generates a battery fault flag that persists until the next clean reboot — it is not a defective cell.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the Capnocheck Plus reports low battery immediately after a confirmed full charge\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe Capnocheck Plus BMS calibrates its state-of-charge reading against stored data from the previous cell. A new Ni-MH pack has not yet established a charge history in that register, so the monitor reads the cell's initial internal resistance as low capacity. This is a BMS learn-cycle issue, not a fault with the cell itself. Running one complete charge-discharge cycle resets the register. After that cycle, the low-battery alarm clears and the monitor reads capacity correctly.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eDevice not completing boot sequence after battery sat in storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells self-discharge at roughly 1–3% per day in storage. A battery left uncharged for several months can drop below 5.0V — the threshold at which the Capnocheck Plus BMS will not initiate a boot sequence at all. The monitor appears completely dead, but the cell is recoverable. Connect the device to mains power and leave it charging for a minimum of four hours before attempting to power on. Once the cell climbs above the BMS recovery threshold, the boot sequence completes normally.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381491859546,"sku":"BWCS-BCM522MD-1","price":80.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381491892314,"sku":"BWCS-BCM522MD-2","price":93.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381491925082,"sku":"BWCS-BCM522MD-3","price":103.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-BCM522MD-1.webp?v=1778901248","url":"https:\/\/batteryweb.com\/products\/bci-capnocheck-plus-replacement-battery-6v-5000mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}