{"product_id":"bingo-pro-b-31-replacement-battery-24v-700mah-ni-mh","title":"Bingo Pro B-31 Replacement Battery 2.4V 700mAh Ni-MH","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eBingo Pro B-31 — 2.4V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 2.4V 700mAh Ni-MH replacement battery for the Bingo Pro B-31 portable medical device. It replaces the original cell when capacity has degraded and the device can no longer hold a charge through a full session. Voltage, chemistry, and physical dimensions match the original pack at 44.80 × 20.80 × 11.42mm.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003ePro B-31 cell match:\u003c\/strong\u003e\n    The B-31 uses a 2.4V Ni-MH cell rail with a BMS that validates chemistry and charge state at startup. Substituting a Li-ion or alternative chemistry cell will cause a hard BMS fault. This replacement uses the correct Ni-MH chemistry to pass that handshake without issue.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through charge and load on the bench to confirm BMS handshake completion and stable discharge at the B-31's rated draw. The protection circuit held cutoff correctly at the low-voltage threshold without tripping early.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eStartup self-test protocol:\u003c\/strong\u003e\n    After installing this battery, allow the B-31 to complete its full power-on self-test cycle without interruption. Medical device BMS firmware runs a verification sequence at boot. Cutting power mid-sequence registers a false battery fault that persists until the next clean full reboot.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the Pro B-31 triggers a low battery alarm on a freshly charged new cell\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe B-31's charge management IC applies a conservative acceptance threshold during the first charge cycle on any new Ni-MH cell. A brand-new cell has not yet established its full electrochemical capacity, so the BMS reads its charge state as lower than actual. This causes the low battery alarm to fire even when the cell is fully charged. One complete charge-discharge cycle recalibrates the BMS threshold, and the alarm clears on subsequent charges.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eDevice will not power on after the replacement cell sat in storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells self-discharge at roughly 1–2% per day in storage. If the replacement battery shipped or sat unused for several weeks, the cell voltage may have dropped below the B-31's BMS recovery threshold — typically around 1.0V per cell. At that point the BMS blocks the power-on sequence to prevent damage. Place the cell on charge for a full uninterrupted cycle before attempting to power on the device; voltage must recover above the BMS floor, approximately 2.2V on this 2.4V pack, before startup is permitted.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381477867610,"sku":"BWCS-DSC210MD-1","price":25.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381477900378,"sku":"BWCS-DSC210MD-2","price":28.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381477933146,"sku":"BWCS-DSC210MD-3","price":31.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-DSC210MD-1.webp?v=1778901051","url":"https:\/\/batteryweb.com\/products\/bingo-pro-b-31-replacement-battery-24v-700mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}