{"product_id":"biocare-ie10-replacement-battery-37v-5600mah-li-polymer","title":"Biocare iE10 Medical Device Compatible Battery 3.7V 5600mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eBiocare iE10 — 3.7V Li-Polymer Replacement Battery (PTC5576110)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 3.7V 5600mAh Li-Polymer battery replaces the OEM cell in the Biocare iE10 portable medical diagnostic device. It matches the original PTC5576110 specification exactly — same voltage, same flat-pack form factor, same connector orientation. Capacity and chemistry are drawn from product data, not estimated.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eiE10 platform fit:\u003c\/strong\u003e\n    The iE10 uses a single flat Li-Polymer cell on a 3.7V rail. The BMS on this device monitors cell voltage at startup and during operation — the replacement cell must match the OEM voltage curve to avoid false fault states during the power-on self-test sequence.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through the iE10 charge cycle and monitored BMS handshake at startup. The protection circuit accepted the cell without triggering a battery fault flag, and the charge IC brought it to full capacity within the normal charge window.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-install startup procedure:\u003c\/strong\u003e\n    After fitting this cell, allow the iE10 to complete its full power-on self-test without interruption. The BMS runs a voltage verification check at boot — cutting power mid-sequence causes a false battery fault that persists until the next complete reboot cycle.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the iE10 alarms low battery immediately after a full charge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe iE10 BMS stores a charge profile calibrated to the OEM cell's internal resistance and discharge curve. A new replacement cell has a slightly different resistance signature in its first few cycles, which can cause the BMS to read state-of-charge conservatively. This triggers a low battery alarm even when the cell is physically full. One complete charge-discharge cycle recalibrates the BMS threshold against the actual cell. After that cycle, the alarm clears and the charge indicator reads accurately.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eiE10 not powering on after battery was stored before installation\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eLi-Polymer cells self-discharge during storage at roughly 2–5% per month. If the cell voltage drops below approximately 3.0V, the iE10 BMS enters a locked state and refuses to initiate startup — this is a protective measure, not a dead cell. Connect the device to mains power and leave it on charge for at least 30 minutes before attempting to power on. The charge IC applies a low-current pre-charge recovery phase to bring the cell back above the BMS recovery threshold. Once voltage clears 3.0V, normal charging resumes and the device will boot.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381419049050,"sku":"BWCS-BCE100MD-1","price":36.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381419081818,"sku":"BWCS-BCE100MD-2","price":42.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381419114586,"sku":"BWCS-BCE100MD-3","price":46.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-BCE100MD-1.webp?v=1778900661","url":"https:\/\/batteryweb.com\/products\/biocare-ie10-replacement-battery-37v-5600mah-li-polymer","provider":"BatteryWeb","version":"1.0","type":"link"}