{"product_id":"bissell-iconpet-cordless-2062n-replacement-battery-252v-3000mah-li-ion","title":"Bissell ICONpet 2062N Replacement Battery 25.2V 3000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eBissell ICONpet Cordless 2062N — 25.2V Li-ion Replacement Battery (61-0088-012)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 25.2V 3000mAh lithium-ion battery replaces the original pack in the Bissell ICONpet Cordless 2062N stick vacuum. It also fits several P2822 platform variants including the 261H004-P2822-0H and P2822-7S1P-02-0A. Capacity is 75.6Wh — matching OEM spec so motor draw and suction performance stay consistent.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eP2822 platform compatibility:\u003c\/strong\u003e\n    The 2062N and its P2822-series variants share the same 7-cell 25.2V architecture, connector pin-out, and BMS communication protocol. A battery built to this spec fits all of them without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge and discharge cycles on a 2062N unit. The BMS handshake initialised correctly, charge acceptance was within spec, and overcurrent protection triggered at the expected draw threshold during blockage simulation.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging habit on the ICONpet:\u003c\/strong\u003e\n    Do not leave the vacuum sitting on the charging dock permanently. The 2062N dock does not terminate charge actively — continuous trickle current accelerates cell degradation. Charge to full, then remove it from the dock.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator reaches low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens when motor voltage sag occurs under load before the BMS triggers the low-battery warning. A partially blocked filter or tangled brush roll forces the motor to draw more current than rated, pulling cell voltage down faster than the indicator tracks. The vacuum loses suction noticeably while the LED still shows adequate charge. Clear the filter and brush roll first — if suction recovers immediately, the battery was not the cause.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cutting out mid-clean then recovering after a short pause\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a dead battery. When sustained airflow restriction — usually a clogged post-motor filter — forces current above the BMS threshold, the pack shuts output to protect the cells. The vacuum restarts once the BMS resets, typically within 30–60 seconds. Clean both the pre-motor foam filter and the post-motor HEPA filter, then confirm the battery rests at 25.2V fully charged before ruling out a cell fault.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43427963502682,"sku":"BWCS-BSP206VX-1","price":80.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43427963535450,"sku":"BWCS-BSP206VX-2","price":94.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43427963568218,"sku":"BWCS-BSP206VX-3","price":104.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-BSP206VX-1.webp?v=1779933519","url":"https:\/\/batteryweb.com\/products\/bissell-iconpet-cordless-2062n-replacement-battery-252v-3000mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}