{"product_id":"blaupunkt-cc-664-replacement-battery-6v-4200mah-ni-mh","title":"Blaupunkt CC-664 Replacement Battery 6V 4200mAh Ni-MH","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eBlaupunkt CC-664 \/ CC-684 \/ CC-695 \/ SC-625 — 6V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 6V 4200mAh Ni-MH replacement battery for the Blaupunkt CC-664, CC-684, CC-695, and SC-625 camcorders. It slots into the same battery compartment as the original and draws from the same voltage rail. Capacity is rated at 4200mAh (25.2Wh) — matching the original specification.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eCC-664 \/ CC-684 \/ CC-695 \/ SC-625 compatibility:\u003c\/strong\u003e\n    These Blaupunkt camcorder models share the same 6V battery platform, connector pinout, and BMS communication protocol. One cell fits all four without adapter or wiring modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through full charge and discharge runs on the CC-664 platform. The BMS accepted the cell without fault flags, and voltage delivery held steady through both recording and standby draw.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-use charge cycle on camcorder models:\u003c\/strong\u003e\n    Insert the battery and run a full charge from within the camera body or OEM charger before your first recording session. Ni-MH cells can present a slightly suppressed voltage on initial installation — one full charge cycle from the body lets the BMS calibrate the remaining-charge indicator correctly.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the CC-664 battery indicator drops suddenly mid-recording\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells have a flatter discharge curve than Li-ion. The CC-664's battery indicator is mapped against voltage thresholds tuned to the original cell's curve. A replacement cell — even at full capacity — can cause the indicator to read lower than actual charge during the first few cycles. This is not a fault with the cell. After two or three full charge-discharge cycles, the BMS recalibrates and the indicator tracks accurately. If the drop persists beyond three cycles, check that the terminal voltage under load stays above 5.4V.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCamcorder shows no battery or refuses to power on with new cell installed\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells can arrive from storage at a low resting voltage — sometimes below the BMS acceptance threshold on the CC-664 platform. The body reads the voltage as too low to boot and blocks power-on as a protection measure. Place the battery in the OEM charger externally for 30–60 minutes to bring it above the minimum boot threshold before inserting it into the body. Once the cell reaches approximately 6.0V resting, the camcorder will power on normally.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43333883854938,"sku":"BWCS-PDHV40-1","price":33.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43333883887706,"sku":"BWCS-PDHV40-2","price":39.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43333883920474,"sku":"BWCS-PDHV40-3","price":43.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-PDHV40-1.webp?v=1778213554","url":"https:\/\/batteryweb.com\/products\/blaupunkt-cc-664-replacement-battery-6v-4200mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}