{"product_id":"bostitch-btc400-replacement-battery-20v-5000mah-li-ion","title":"Bostitch 20V Brad Nailer Replacement Battery 5000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eBostitch BTC400 Series — 20V Li-ion 5000mAh Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 20V Li-ion replacement battery rated at 5000mAh (100Wh) for the Bostitch BTC400 series cordless brad nailers. It fits the BTC400, BTC401, BTC401LA, and BTC440, among others. The cell pack slots into the same battery bay and communicates with the same BMS handshake as the original Bostitch 20V platform.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eBTC400 series platform fit:\u003c\/strong\u003e\n    These nailer models share the same 20V battery rail, mechanical latch geometry, and BMS data line. One cell pack works across the full range because Bostitch did not change the connector or communication protocol between these variants.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through charge and discharge cycles on a BTC400 chassis. The BMS negotiated correctly on first connection, overcurrent protection tripped at the expected threshold during simulated fast-firing sequences, and cell balance held within spec across full discharge.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBrad nailer break-in on first use:\u003c\/strong\u003e\n    On first use, run the nailer at a moderate firing rate for two cycles before sustained rapid-fire applications. This gives the BMS time to profile the inrush current spike from the driver mechanism and set accurate overcurrent thresholds before you push it hard.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBMS overcurrent trip on rapid-fire trigger pulls\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eEvery trigger pull on a brad nailer sends a short, sharp current spike to the driver motor. On a new or cold pack, the BMS overcurrent threshold may not yet be calibrated to the motor's inrush profile, so it cuts power mid-sequence. This is not a faulty cell — it is the protection circuit being conservative. Two to three moderate break-in cycles allow the BMS to log the motor's actual inrush curve and stop tripping on legitimate fast-fire bursts.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCharger blinks red and won't accept a new pack after storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eLi-ion cells self-discharge during storage, and if a pack drops below approximately 2.5V per cell, most Bostitch 20V chargers refuse to begin a standard charge cycle — the red blink is the charger rejecting a pack it reads as unsafe. Some chargers include a recovery or \"wake\" mode that trickle-charges at low current until the pack climbs back above the acceptance threshold, typically around 3.0V per cell. If yours does not, a compatible charger with a recovery function will bring the pack back up. Once cell voltage reaches 3.0V per cell, the charger will accept the pack and complete a normal charge cycle.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43416039293018,"sku":"BWCS-BPL120PH-1","price":52.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43416039325786,"sku":"BWCS-BPL120PH-2","price":60.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43416039358554,"sku":"BWCS-BPL120PH-3","price":66.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-BPL120PH-1.webp?v=1779759664","url":"https:\/\/batteryweb.com\/products\/bostitch-btc400-replacement-battery-20v-5000mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}