{"product_id":"burdick-corp-elite-ek10-replacement-battery-12v-3000mah-ni-mh","title":"Burdick Elite EK10 Replacement Battery 12V 3000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eBurdick Corp Elite EK10 — 12V Ni-MH Replacement Battery (862278)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 12V, 3000mAh Ni-MH replacement battery for the Burdick Corp Elite EK10 electrocardiograph. It also fits the Elite 2 and EK10 variants. The battery powers cordless operation during patient examinations in clinical settings.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eEK10 and Elite 2 platform fit:\u003c\/strong\u003e\n    These models share the same 12V power rail, connector pinout, and BMS handshake protocol — one battery cell pack services all listed variants without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through full charge-discharge on the EK10 platform and confirmed the BMS accepted the new cell, completed its verification routine, and cleared all battery fault flags by the second cycle.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePower-on self-test protocol:\u003c\/strong\u003e\n    After installing this battery, let the EK10 complete its full startup self-test without interruption. The device runs a BMS verification sequence at boot — cutting power during that window triggers a battery fault flag that persists until the next clean reboot.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSelf-test failure after battery swap in the EK10\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe EK10's BMS runs a capacity verification check during startup. A new Ni-MH cell hasn't yet established its full charge-acceptance profile, so the BMS can flag it as non-conforming on the first one or two boot cycles. This isn't a defective battery — it's the BMS reading a cell that hasn't completed its initial conditioning cycle. Run one full charge-discharge cycle before using the device clinically, and the self-test will pass cleanly from that point forward.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eLow battery alarm triggers immediately after a confirmed full charge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens when the BMS threshold is calibrated to OEM cell chemistry and the new cell hasn't yet matched that discharge curve. On the first cycle, the BMS reads internal resistance and resting voltage against stored OEM parameters — a fresh Ni-MH cell often sits slightly outside those limits before conditioning. The alarm clears once the cell completes one full charge-discharge cycle and the BMS recalibrates to the new cell's actual curve. Charge fully to 12V, discharge under normal device load, then recharge fully before trusting the indicator.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381506703450,"sku":"BWCS-MEK100MD-1","price":83.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381506736218,"sku":"BWCS-MEK100MD-2","price":97.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381506768986,"sku":"BWCS-MEK100MD-3","price":108.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-MEK100MD-1.webp?v=1778901341","url":"https:\/\/batteryweb.com\/products\/burdick-corp-elite-ek10-replacement-battery-12v-3000mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}