{"product_id":"canon-speedlite-el1-replacement-battery-72v-2600mah-li-ion","title":"Canon Speedlite EL-1 LP-EL Replacement Battery 7.2V 2600mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eCanon Speedlite EL-1 — 7.2V Li-ion Replacement Battery (LP-EL)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 7.2V 2600mAh Li-ion battery replaces the Canon LP-EL cell in the Speedlite EL-1 external flash unit. It powers the xenon tube, capacitor recharge circuit, and onboard electronics. Fits Speedlite EL-1 and DS401231 units.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eSpeedlite EL-1 and DS401231 compatibility:\u003c\/strong\u003e\n    Both units draw from the same 7.2V rail and use the same LP-EL form factor with an identical BMS handshake protocol — one cell fits both without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through repeated full-power flash sequences and monitored BMS cutoff behaviour under capacitor recharge current. The cell held voltage within the expected window across sustained burst shooting.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-use power cycle on the EL-1:\u003c\/strong\u003e\n    After fitting this cell, power the flash fully off, wait five seconds, then power on from cold. The EL-1's BMS completes its handshake only on a clean cold start — swapping the cell while the flash is in standby can leave the charge circuit in a fault state.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eFlash output stepping down after 10–15 full-power shots\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe EL-1 recharges its capacitor after every shot, and at full power that recharge draw is substantial — roughly 3–5A in short bursts. A cell with elevated internal resistance cannot sustain that current without voltage dropping below the BMS protection threshold. When that happens, the flash firmware steps output down automatically to protect the circuit. A fresh LP-EL cell with low internal resistance handles the recharge spike without the sag. If output stepping continues after five conditioning cycles, check that the cell contacts are clean and fully seated.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eRecycle time noticeably slower with a new cell straight out of the box\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNew Li-ion cells ship with slightly elevated internal resistance until the electrolyte fully wets the electrode stack — typically resolves over three to five full charge and discharge cycles. During those first cycles, the capacitor recharge current causes a small voltage sag that the flash interprets as a slower available power budget, extending recycle time. Run five complete sessions with full charge before judging final recycle performance. After conditioning, recycle time on a 2600mAh LP-EL cell at 7.2V should match Canon's published specification for the EL-1.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43416245764186,"sku":"BWCS-CDS401SL-1","price":49.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43416245796954,"sku":"BWCS-CDS401SL-2","price":58.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43416245829722,"sku":"BWCS-CDS401SL-3","price":64.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-CDS401SL-1.webp?v=1779761098","url":"https:\/\/batteryweb.com\/products\/canon-speedlite-el1-replacement-battery-72v-2600mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}