{"product_id":"carneo-smartcleaner-610-replacement-battery-144v-3500mah-ni-mh","title":"Carneo SmartCleaner 610 Replacement Battery 14.4V 3500mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eCarneo SmartCleaner 610 — 14.4V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 14.4V 3500mAh Ni-MH replacement battery for the Carneo SmartCleaner 610 robotic vacuum cleaner. It fits directly into the SmartCleaner 610 and restores autonomous cleaning operation when the original cell has lost capacity or failed completely. Voltage and capacity match the factory specification.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eSmartCleaner 610 fitment:\u003c\/strong\u003e\n    The SmartCleaner 610 uses a 14.4V Ni-MH pack at this physical footprint — 90.06 x 69.53 x 45.45mm. The BMS in this robot expects a Ni-MH cell chemistry; swapping to a different chemistry without a firmware-aware charger will cause charge rejection or incorrect cut-off behaviour.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through full charge and discharge cycles on the SmartCleaner 610 platform. The BMS accepted the cell without fault codes, and the motor draw stayed within the expected current envelope across both hard floor and carpet test passes.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging behaviour on Ni-MH:\u003c\/strong\u003e\n    Remove the SmartCleaner 610 from its charging dock once the charge cycle completes. Ni-MH cells on continuous trickle charge from a dock develop capacity fade faster than cells charged only when depleted — this applies directly to how the SmartCleaner 610's dock handles a full pack.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator reaches low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe SmartCleaner 610 motor pulls more current when airflow is restricted — a partially blocked filter is the most common cause. Under that extra load, Ni-MH cells show voltage sag earlier than the charge indicator predicts, so suction weakens while the indicator still reads mid-charge. The vacuum interprets this as normal operation and does not flag a low-battery warning. Clean or replace the filter first; if suction recovers and the battery indicator aligns with actual run behaviour, the cell is fine.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cuts out mid-cycle then recovers after a short pause\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a failed battery. Sustained restricted airflow — usually a blocked brush roll or clogged filter — forces the motor to draw above the BMS current threshold, triggering a protective cutoff. The pack resets after the thermal and current conditions drop, which is why the vacuum restarts after a pause. Clear the brush roll and filter, then check that the restart happens normally; if the trip occurs again on a clean filter, measure pack voltage at rest — it should read above 13.5V on a fully charged Ni-MH 14.4V pack.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43428043554906,"sku":"BWCS-KSB002VX-1","price":86.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43428043587674,"sku":"BWCS-KSB002VX-2","price":101.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43428043620442,"sku":"BWCS-KSB002VX-3","price":112.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-KSB002VX-1.webp?v=1779933966","url":"https:\/\/batteryweb.com\/products\/carneo-smartcleaner-610-replacement-battery-144v-3500mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}