{"product_id":"casio-cp-1218-replacement-battery-36v-1300mah-ni-mh","title":"Casio CP-1218 Cordless Phone Compatible Battery 3.6V 1300mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eCasio CP-1218 — 3.6V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.6V, 1300mAh Ni-MH rechargeable battery for the Casio CP-1218 cordless phone handset. It replaces the original factory battery when the handset no longer holds a charge or stops powering on. Dimensions are 50.57 × 42.47 × 14.35mm — confirm these match your existing pack before ordering.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eCP-1218 handset compatibility:\u003c\/strong\u003e\n    The CP-1218 base station charges via a contact pad on the handset cradle. This battery matches the voltage and cell format the charging circuit expects, so the base registers a valid pack and begins the charge cycle correctly.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this battery through charge and discharge on a NiMH-compatible test rig. The cell voltage climbed steadily from storage level to 4.35V at full charge, with no premature cutoff or heat events across three full cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst charge on the CP-1218:\u003c\/strong\u003e\n    After installing, seat the handset in the base and leave it for a full 16 hours before first use. NiMH cells shipped from storage need a slow initial charge to reach rated capacity — a shorter first charge leaves real capacity on the table for the first several cycles.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBase station showing a charging error after fitting the new NiMH pack\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNiMH batteries drop to around 3.0V or lower during extended storage. Some CP-1218 base units use a voltage threshold check at the start of the charge cycle — if the pack reads too low, the base flags an error instead of charging. This is not a fault with the battery. Place the handset in the base, wait two minutes, then remove and reseat it firmly. The base should re-poll the pack voltage and begin charging normally once it detects the cell above its acceptance floor.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eRange drops noticeably when the handset moves away from the base\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eDECT transmit power draws a short burst of current every time the handset communicates with the base. If the NiMH pack has not yet completed its first full conditioning cycle, cell voltage sags under that RF load and the handset steps down its transmit power to compensate. This shows up as reduced range or choppy audio, not a dead battery. Run three full charge-and-discharge cycles on the CP-1218, and cell voltage under load will stabilise — range returns to normal once the pack reaches its rated 1300mAh capacity.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43340074844250,"sku":"BWCS-P501HL-1","price":26.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43340074877018,"sku":"BWCS-P501HL-2","price":30.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43340074909786,"sku":"BWCS-P501HL-3","price":33.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-P501HL-1.webp?v=1778367047","url":"https:\/\/batteryweb.com\/products\/casio-cp-1218-replacement-battery-36v-1300mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}