{"product_id":"caterpillar-cat-s48c-replacement-battery-38v-3800mah-li-polymer","title":"CAT S48c Replacement Battery L6880 3.8V 3800mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eCATERPILLAR CAT S48c — 3.8V Li-Polymer Replacement Battery (L6880)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.8V, 3800mAh Li-Polymer battery for the CATERPILLAR CAT S48c rugged smartphone. It replaces OEM part number L6880 when the original cell degrades and can no longer hold adequate charge. Dimensions are 98.16 × 57.80 × 4.30mm — measure your original before fitting if you are unsure.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eCAT S48c platform fit:\u003c\/strong\u003e\n    The S48c uses a fixed 3.8V nominal rail with a BMS that handshakes on a single-wire data line. This cell matches that connector pinout and voltage profile, so the fuel gauge IC can read state-of-charge correctly from the first boot.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell on the S48c motherboard and monitored BMS communication throughout. The charge IC accepted the cell on the first cycle and the coulomb counter initialised without a fault flag.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-cycle fast-charge protocol:\u003c\/strong\u003e\n    On first use after installation, disable fast charging and run one full discharge-charge cycle at standard rate. This lets the fuel gauge IC map the new cell's discharge curve before high-current fast charging pushes current into an uncalibrated cell.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSudden shutdown at 20–30% on the CAT S48c after a cell swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe CAT S48c's fuel gauge IC holds a discharge curve calibrated to the original cell. A new cell with a slightly different impedance profile hits a voltage cliff at a different state-of-charge than the stored map expects. When the modem fires a high-current burst — a call, a data handshake — terminal voltage sags below the shutdown threshold even though the reported percentage reads 20–30%. One full discharge-charge cycle at standard rate forces the coulomb counter to rebuild the curve against the new cell, and sudden shutdowns typically stop after that recalibration pass.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003ePhone not powering on after the replacement battery sat in storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eLi-Polymer cells self-discharge in storage. If a replacement cell drops below approximately 2.5V per cell during storage, the BMS enters lockout to prevent damage and the phone will not power on. Plug the device into a wall charger — not a USB port — and leave it for 15–20 minutes without pressing the power button. The charge IC applies a trickle current that nudges the cell above the BMS recovery threshold, at which point the BMS releases lockout and normal charging resumes. If the charge LED does not light within 30 minutes on a wall charger, check the charger output is at least 5V 1A.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43391881314394,"sku":"BWCS-CAS480SL-1","price":29.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43391881347162,"sku":"BWCS-CAS480SL-2","price":33.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43391881379930,"sku":"BWCS-CAS480SL-3","price":36.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-CAS480SL-1.webp?v=1779142479","url":"https:\/\/batteryweb.com\/products\/caterpillar-cat-s48c-replacement-battery-38v-3800mah-li-polymer","provider":"BatteryWeb","version":"1.0","type":"link"}