{"product_id":"cordex-toughpix-digitherm-replacement-battery-37v-1800mah-li-ion","title":"CorDex CDX370 Thermal Camera Compatible Battery 3.7V 1800mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eCorDex ToughPix DigiTherm — 3.7V Li-ion Replacement Battery (CDX370)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 3.7V, 1800mAh Li-ion battery replaces the CDX370 cell in the CorDex ToughPix DigiTherm thermal imaging camera. It fits the ToughPix DigiTherm directly and restores full camera operation for field inspections. Capacity figures are sourced from product data — 1800mAh at 3.7V, totalling 6.66Wh.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eToughPix DigiTherm compatibility:\u003c\/strong\u003e\n    The DigiTherm runs its thermal detector array and LCD display from a single 3.7V cell. Both loads share one power rail, so the replacement cell must match the original voltage and BMS communication profile exactly — otherwise the camera rejects the pack on startup.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this battery under simultaneous detector and display load on the DigiTherm platform. The BMS held voltage above the thermal detector's minimum threshold throughout the draw cycle and tripped protection cleanly at end-of-discharge without dropping the camera mid-frame.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eThermal detector warm-up after swap:\u003c\/strong\u003e\n    After fitting a fresh battery, allow the camera 60 seconds at idle before taking measurements. The microbolometer detector needs the internal board temperature to stabilise — readings taken immediately after power-on will drift until the electronics reach thermal equilibrium.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eThermal accuracy degrading before the battery indicator shows low\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe DigiTherm's thermal detector is voltage-sensitive. As the cell discharges toward the mid-range, detector bias voltage drops slightly ahead of what the fuel gauge reports. This causes temperature readings to drift before the low-battery icon ever appears. The camera display and detector draw from the same cell, and the detector loses calibration accuracy first. If readings look inconsistent, check cell voltage directly — anything below 3.5V under load warrants a swap.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCamera shutting down mid-inspection with no low-battery warning\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens when the BMS trips on a combined load spike — the thermal detector's heating element plus the display can briefly push current draw beyond what a degraded or cold cell can sustain. The BMS cuts power to protect the cell rather than warn first. It is not a camera fault. Warm the replacement battery to room temperature before fitting it in cold environments, and confirm the resting cell voltage is at or above 3.7V before starting an inspection.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43426106736730,"sku":"BWCS-CDX370SL-1","price":32.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43426106769498,"sku":"BWCS-CDX370SL-2","price":37.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43426106802266,"sku":"BWCS-CDX370SL-3","price":41.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-CDX370SL_1.webp?v=1779930364","url":"https:\/\/batteryweb.com\/products\/cordex-toughpix-digitherm-replacement-battery-37v-1800mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}