{"product_id":"custom-battery-packs-replacement-battery-96v-1500mah-ni-mh","title":"9.6V Ni-MH Replacement Battery Pack AA15008S1P 1500mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eCustom Battery Packs AA15008S1P — 9.6V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 9.6V 1500mAh (14.4Wh) Ni-MH replacement battery pack built to the AA15008S1P specification. It targets cordless devices that accept this OEM part number directly — handheld tools, emergency lighting units, and consumer electronics running on a 9.6V rechargeable pack. Match your original part number before ordering.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003e9.6V Ni-MH cell configuration:\u003c\/strong\u003e\n    Eight NiMH cells wired in series produce the 9.6V nominal rail this pack runs on. Devices that accept the AA15008S1P are voltage-matched to this rail at the charge controller level — swapping to a different voltage pack will trip the charge IC or damage the device.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through charge and discharge on a cell analyser. The BMS held cell balancing within spec, and capacity measured at rated across three consecutive cycles after an initial conditioning charge.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-use calibration cycle:\u003c\/strong\u003e\n    Run a full charge to termination, then discharge the pack completely before recharging. Ni-MH packs ship at storage voltage, and devices with a capacity indicator will misread the state of charge until one full cycle resets the fuel gauge baseline.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003ePack running at lower voltage than rated on first install\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH packs leave the warehouse at storage voltage — typically 1.0–1.1V per cell, which puts a fresh 9.6V pack closer to 8.0–8.8V at the terminals. Some devices flag this as a fault or refuse to operate normally. This is not a defect. Charge the pack fully before first use and let the charger reach termination. After a full charge, terminal voltage should read 9.6V or slightly above under no load.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003ePack not accepted by device after swap\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eIf the device shows no response or a fault indicator after installing a new pack, the most common cause is a BMS handshake check failing on a cold, partially discharged cell. The device reads the pack voltage, sees it below the acceptance threshold, and rejects it. Charge the pack fully via the OEM charger first — do not install and expect the device to charge from flat. Once the pack reaches full charge, reinstall and power cycle the device to clear the rejection state.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43333476745306,"sku":"BWCS-CM044SL-1","price":39.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43333476778074,"sku":"BWCS-CM044SL-2","price":45.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43333476810842,"sku":"BWCS-CM044SL-3","price":50.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-CM044SL-1.webp?v=1778212808","url":"https:\/\/batteryweb.com\/products\/custom-battery-packs-replacement-battery-96v-1500mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}