{"product_id":"datalogic-lynx-replacement-battery-37v-4000mah-li-polymer","title":"Datalogic LYNX 50-BTEC Replacement Battery 3.7V 4000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eDatalogic LYNX — 3.7V Li-Polymer Replacement Battery (50-BTEC)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 3.7V 4000mAh Li-Polymer battery replaces the original pack in the Datalogic LYNX handheld barcode scanner. It fits the LYNX mobile computer used in warehouse, logistics, and point-of-sale environments. OEM part numbers 50-BTEC, 50-BTSC, and 94ACC0065 all cross to this replacement.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eLYNX platform compatibility:\u003c\/strong\u003e\n    The LYNX uses a single-cell Li-Polymer architecture at 3.7V nominal. The BMS handshake on this platform authenticates via the connector's third pin — this replacement meets that signal requirement so the device boots without a battery-fault warning.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through scan-trigger bursts combined with active wireless polling. The BMS held stable across both simultaneous draws and did not trip a false low-voltage cutoff during the inrush peaks.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-shift preparation:\u003c\/strong\u003e\n    After installing this pack, seat the scanner in its cradle and run a full charge cycle before the first shift. The scan trigger inrush current is highest when the cell is near minimum charge, and a fully primed cell prevents the BMS from tripping on the very first trigger pull of the day.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCradle showing a charging error on a brand-new pack\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eA charging error on a new pack is almost always a contact resistance problem, not a faulty cell. The LYNX cradle reads battery state through the pack's contact pads, and any film — skin oil, warehouse dust, static charge residue — raises resistance enough to trigger a fault code. Wipe the gold contacts on both the battery and the cradle dock with a dry lint-free cloth, then reseat the pack firmly. If the error clears, the cell is fine and the dock has resumed communication.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eScanner dropping wireless connection during rapid scan bursts\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe LYNX draws current from two sources simultaneously during a rapid scan burst: the imager or laser and the wireless radio. Combined, these can cause a momentary voltage sag on an underpowered or partially charged cell. When the cell voltage dips below the radio module's minimum operating threshold — approximately 3.2V under load — the wireless stack drops before the BMS fully trips. Charge the pack to 100% before a high-volume session, and if sags persist on an older pack, the cell has likely capacity-faded below the point where it can sustain both draws together.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43324738568282,"sku":"BWCS-DAX100BX-1","price":64.99,"currency_code":"USD","in_stock":false},{"title":"Warranty 2 Year","offer_id":43324738601050,"sku":"BWCS-DAX100BX-2","price":76.99,"currency_code":"USD","in_stock":false},{"title":"Warranty 3 Year","offer_id":43324738633818,"sku":"BWCS-DAX100BX-3","price":85.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-DAX100BX-1.webp?v=1778123055","url":"https:\/\/batteryweb.com\/products\/datalogic-lynx-replacement-battery-37v-4000mah-li-polymer","provider":"BatteryWeb","version":"1.0","type":"link"}