{"product_id":"digital-ally-dvm-rmt-replacement-battery-36v-600mah-ni-mh","title":"Digital Ally DVM-RMT Compatible Battery 3.6V 600mAh Ni-MH","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eDigital Ally DVM-RMT \/ DVM 500 — 3.6V Ni-MH Replacement Battery (CS2\/3F6 3S1P)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.6V, 600mAh Ni-MH replacement battery for the Digital Ally DVM-RMT wireless remote and DVM 500 system. It fits the remote control unit used to trigger recording on Digital Ally body and dash camera setups. OEM part numbers CS2\/3F6 3S1P and 135-0035 both cross-reference to this cell.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eDVM-RMT and DVM 500 remote compatibility:\u003c\/strong\u003e\n    Both remotes share the same 3.6V three-cell Ni-MH pack configuration with identical connector and physical footprint, which is why one replacement cell covers both units.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge and discharge cycles on the DVM-RMT remote and confirmed the BMS accepted the cell without fault codes or cutoff events at normal remote operating loads.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eNi-MH conditioning on first install:\u003c\/strong\u003e\n    Ni-MH cells in low-draw remotes can show inaccurate charge indicators if installed partially charged. Run one full charge cycle in the OEM charger before using the remote in the field — this lets the charge circuit calibrate to the new cell's capacity curve.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the DVM-RMT remote stops responding before the battery reads empty\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells have a relatively flat discharge curve, which means the remote's voltage-threshold indicator can read mid-charge right up until the cell drops below the radio transmission floor. The remote's RF transmitter draws a short high-current burst each time you press a button — at end of cell life, that burst pulls the voltage below the minimum the transmitter needs, and the signal never reaches the camera. The cell is not truly dead, but it cannot sustain the transmission pulse. Replace or recharge the cell when button presses become intermittent, even if the indicator still shows charge remaining.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eRemote charges but camera body stops acknowledging button presses after storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells self-discharge at roughly 1–3% per day at room temperature. A remote left unused for several weeks can drop to a state low enough that the first few charge cycles do not fully recover capacity. This is not a fault with the replacement cell — it is a known Ni-MH behaviour after deep self-discharge. Charge the battery fully, then run it down through normal remote use before charging again. After two to three full cycles, the cell reaches its rated 600mAh and button response to the camera system returns to normal.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43333801148506,"sku":"BWCS-DVM300MC-1","price":28.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43333801181274,"sku":"BWCS-DVM300MC-2","price":32.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43333801214042,"sku":"BWCS-DVM300MC-3","price":34.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-DVM300MC_1.webp?v=1778213127","url":"https:\/\/batteryweb.com\/products\/digital-ally-dvm-rmt-replacement-battery-36v-600mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}