{"product_id":"eads-mc900-replacement-battery-36v-700mah-ni-mh","title":"EADS MC900 Cordless Phone Compatible Battery 3.6V 700mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eEADS MC900 \/ MC901 \/ MC902 — 3.6V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.6V, 700mAh Ni-MH battery for the EADS MC900, MC901, and MC902 cordless handsets. It slots into the handset battery compartment and restores wireless operation from the base station. Dimensions are 46.60 × 31.40 × 10.60mm — check these against your existing pack before ordering.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eMC900, MC901, MC902 compatibility:\u003c\/strong\u003e\n    These three models share the same handset chassis, battery bay dimensions, and 3.6V supply rail. One pack fits all three without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through charge and discharge on the MC900 platform. The handset accepted the battery, the base station initiated charging normally, and voltage held steady under talk-mode RF load.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-charge protocol for Ni-MH handsets:\u003c\/strong\u003e\n    After installing, seat the handset in the base and leave it for a full 16 hours before first use. Ni-MH cells from storage arrive partially discharged — a slow first charge lets them reach rated capacity. Skipping this step is the single biggest cause of short talk time complaints on new replacement batteries.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eRange reduction after fitting a new Ni-MH pack\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eDECT handsets ramp transmit power to maintain signal at range. When a Ni-MH pack hasn't been fully conditioned, its voltage sags under the RF load burst. The handset interprets this as a weak signal and shortens range before dropping the call entirely. Run three full charge-discharge cycles through the base station and the voltage sag will reduce as the cells condition.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBase station charge light not activating after battery swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH packs sitting in storage can drop below the voltage threshold the base station uses to confirm a valid battery is present. If the charge indicator stays off after seating the handset, remove it, wait 10 seconds, and reseat firmly. If the contacts are clean and the light still doesn't activate, the pack voltage may be too low — connect a compatible external Ni-MH charger at 3.6V to bring it above the acceptance threshold, then return the handset to the base.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43339999838298,"sku":"BWCS-MC902CL-1","price":22.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43339999871066,"sku":"BWCS-MC902CL-2","price":25.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43339999903834,"sku":"BWCS-MC902CL-3","price":27.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-MC902CL-1.webp?v=1778367046","url":"https:\/\/batteryweb.com\/products\/eads-mc900-replacement-battery-36v-700mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}