{"product_id":"electia-home-prosafe-alarm-panel-replacement-battery-72v-700mah-ni-mh","title":"Electia Home Prosafe 7.2V 700mAh Ni-MH Compatible Battery","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eElectia Home Prosafe \/ 1131 DTMF \/ 1132 GSM — 7.2V Ni-MH Replacement Battery (802306063Y3)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 7.2V, 700mAh Ni-MH replacement battery for the Electia Home Prosafe alarm panel and related Electia control panel variants. It slots into the panel's backup power bay and keeps the system live during mains failure. OEM part numbers 802306063Y3 and 802307363Y1 both cross to this cell.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eHome Prosafe, 1131 DTMF, 1132 GSM, C-Fence GSM:\u003c\/strong\u003e\n    These panels share the same 7.2V backup rail and identical connector footprint. The BMS on each variant expects the same float voltage and charge termination profile, so one cell covers all four.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge acceptance and float hold on the Home Prosafe panel. The BMS accepted the cell cleanly, held float voltage without cycling, and the panel cleared its low-battery flag within 36 hours.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-install panel conditioning:\u003c\/strong\u003e\n    Do not trigger a zone test immediately after fitting this cell. Allow 24–48 hours on float charge first. Running a diagnostic test on a freshly installed Ni-MH cell can cause the panel to report low battery before the cell has reached working capacity.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eAlarm panel losing programming during a power cut after battery replacement\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eA freshly fitted Ni-MH cell needs 48 hours on the panel's float charger before it can sustain load during mains failure. If the panel loses its programmed zones or user codes during an outage in that window, the battery has not yet been fully conditioned — it cannot hold enough charge to power the processor through a real interruption. This is not a fault with the cell. Restore mains power, leave the panel on for 48 hours, then test again. After conditioning, the panel should retain all programming through a full mains-off event.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSiren not sounding on test after fitting a new backup cell\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eSome Electia panels apply a 30–60 second siren delay on backup power when the battery voltage is below the panel's confirmed-charge threshold. A new cell fresh out of packaging sits below that threshold. The panel registers the battery as unconfirmed and suppresses the siren output as a precaution. This is not a wiring fault or a failed cell. Leave the panel powered for at least 24 hours, then repeat the siren test — the delay clears once the battery reads above the panel's minimum float threshold, typically 7.0V under light load.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43309829095514,"sku":"BWCS-EPR113BT-1","price":24.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43309829128282,"sku":"BWCS-EPR113BT-2","price":27.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43309829161050,"sku":"BWCS-EPR113BT-3","price":30.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-EPR113BT-1.webp?v=1777868235","url":"https:\/\/batteryweb.com\/products\/electia-home-prosafe-alarm-panel-replacement-battery-72v-700mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}