{"product_id":"flir-one-pro-replacement-battery-37v-450mah-li-polymer","title":"FLIR One Pro Thermal Camera Compatible Battery 3.7V 450mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eFlir One Pro \/ One Pro LT — 3.7V Li-Polymer Replacement Battery (SDL702035)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 3.7V, 450mAh Li-Polymer cell replaces the SDL702035 and LF602035-02 batteries in the Flir One Pro, One Pro LT, and 435-0012 thermal imaging cameras. It powers the thermal detector, display, and internal electronics that make handheld thermal inspection work possible. Swap it when the original cell no longer holds a usable charge through a full inspection job.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eOne Pro and One Pro LT compatibility:\u003c\/strong\u003e\n    Both models share the same connector pinout, BMS handshake protocol, and 3.7V voltage rail, which is why one cell covers the full range. The SDL702035 footprint — 37 × 20 × 7mm — fits the battery bay without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge and discharge cycles on a One Pro unit. The BMS accepted the cell without fault flags, thermal throttling events cleared correctly, and the camera exited standby cleanly at each test cycle.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eThermal detector warm-up on first power-on:\u003c\/strong\u003e\n    After fitting a new cell, allow the camera to run for at least 60 seconds before taking any measurements. The uncooled thermal detector needs the internal electronics to reach a stable temperature before the baseline calibration is accurate — readings taken immediately after power-on can be off by several degrees.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eThermal camera shutting down mid-inspection on a new battery\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe One Pro pulls current from two sources simultaneously — the display backlight and the resistive heating element that keeps the thermal detector at operating temperature. Under combined load, especially in cold ambient conditions where the heater works harder, instantaneous current draw can spike above the BMS protection threshold. A cell with any internal resistance above spec — including a worn original or a poor-quality replacement — trips the overcurrent cutoff before the fuel gauge reads empty. This replacement cell is rated to handle the combined draw without tripping the cutoff under normal operating conditions.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eThermal accuracy degrading before the battery indicator shows low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe uncooled microbolometer in the One Pro is voltage-sensitive. As cell voltage sags under load — typically below 3.5V — the detector's readout electronics lose enough precision that temperature delta accuracy drops before the battery gauge triggers a low-battery warning. This means the camera can appear to have charge remaining while thermal readings are already drifting. If spot temperatures look inconsistent or hot spots seem to shift between frames, check cell voltage directly rather than relying on the indicator. A fully charged cell should read 4.2V at rest; below 3.6V under load, replace or recharge before continuing measurements.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43426109980762,"sku":"BWCS-FLT130SL-1","price":23.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43426110013530,"sku":"BWCS-FLT130SL-2","price":26.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43426110046298,"sku":"BWCS-FLT130SL-3","price":29.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-FLT130SL-1.webp?v=1779930364","url":"https:\/\/batteryweb.com\/products\/flir-one-pro-replacement-battery-37v-450mah-li-polymer","provider":"BatteryWeb","version":"1.0","type":"link"}