{"product_id":"garmin-quest-replacement-battery-37v-1000mah-li-ion","title":"Garmin Quest Compatible Battery IA3Y117F2 3.7V","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eGarmin Quest — 3.7V Li-ion Replacement Battery (IA3Y117F2)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.7V, 1000mAh Li-ion cell that replaces part number IA3Y117F2 in the Garmin Quest handheld GPS navigator. The Quest is a portable outdoor navigation device used for waypoint tracking and route guidance. Fit this cell when the original no longer holds enough charge to sustain active navigation sessions.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eQuest platform fit:\u003c\/strong\u003e\n    The Quest uses a single-cell 3.7V Li-ion pack with a direct connector to the device's power management circuit. This cell matches that voltage rail and connector, so the device's charge controller communicates with the cell without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through charge and discharge on the bench, confirmed the BMS engaged at the correct low-voltage cutoff, and verified the Quest's charge indicator tracked the state of charge accurately across the full cycle.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eCold-start satellite acquisition after swap:\u003c\/strong\u003e\n    After fitting this cell, power the Quest on outdoors before first use. A full power interruption clears the GPS receiver's almanac data, triggering a cold start — budget 5 to 10 minutes for the first satellite fix versus under a minute for a subsequent warm start.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eGPS accuracy reduced as battery level drops on the Quest\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe Quest's GPS receiver draws consistent power to maintain signal sensitivity. At low cell voltage — typically below 3.5V — some units reduce receiver gain to protect remaining charge. This shows up as position drift or slower fix refresh, not a hardware fault. Keeping the cell above 3.6V during active navigation keeps the receiver running at full sensitivity.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eQuest shutting off without warning before the battery indicator hits empty\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eA new cell's charge indicator needs one or two full cycles before the Quest's fuel gauge calibrates to it. Until then, the device's low-battery threshold can trigger a hard cutoff while the display still shows one bar remaining. Run the Quest down to automatic shutdown, then charge it fully to 4.2V — repeat once more and the indicator will track accurately.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43377666949210,"sku":"BWCS-IQU1SL-1","price":22.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43377666981978,"sku":"BWCS-IQU1SL-2","price":25.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43377667014746,"sku":"BWCS-IQU1SL-3","price":27.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-IQU1SL-1.webp?v=1778771802","url":"https:\/\/batteryweb.com\/products\/garmin-quest-replacement-battery-37v-1000mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}