{"product_id":"goldway-6000f-replacement-battery-12v-2300mah-sealed-lead-acid","title":"Goldway 6000F Replacement Battery 12V 2300mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eGoldway 6000F — 12V Sealed Lead Acid Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 12V, 2300mAh (27.6Wh) sealed lead-acid replacement battery for the Goldway 6000F medical device. It restores power to portable clinical monitoring equipment where the original cell has degraded or failed. Dimensions are 182.21 x 60.74 x 23.58mm — verify clearance inside the device bay before installation.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eGoldway 6000F platform:\u003c\/strong\u003e\n    The 6000F runs a 12V sealed lead-acid architecture with a BMS that validates cell voltage, internal resistance, and charge state at startup. A replacement must match the original voltage and chemistry exactly — substituting a lithium cell on this platform will cause a BMS rejection fault.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this battery through a full charge-discharge sequence and confirmed BMS handshake at startup. The charge IC held charge termination correctly, and voltage held steady under the load profile the 6000F applies during its self-test routine.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-swap startup protocol:\u003c\/strong\u003e\n    After installation, allow the device to complete its full power-on self-test cycle without interruption. The 6000F runs a BMS verification sequence at boot — cutting power mid-sequence registers a battery fault flag that persists until the next clean reboot, not until the next charge.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eDevice not completing boot sequence on a new battery\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe 6000F performs a voltage and impedance check early in its boot sequence. A new sealed lead-acid cell that has been in storage can present a resting voltage low enough to fail this threshold before any load is applied. The device may halt mid-boot or display a battery error even though the cell is not defective. Fully charge the replacement battery before the first installation — connect it to a compatible 12V SLA charger and allow it to reach a resting voltage of at least 12.6V before fitting it to the device.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCharge indicator not reaching 100% on first charge cycle\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe 6000F charge management circuit applies a conservative absorption-phase limit on cells it has not yet profiled. On a new sealed lead-acid battery, this can cause the indicator to plateau at 90–95% and stop climbing. This is not a fault with the battery or the charger — it resolves after one complete charge-discharge cycle as the charge IC updates its cell model. Run one full discharge under normal device use, then recharge to completion; the indicator should reach 100% on the second cycle.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381513322586,"sku":"BWCS-NK9130MD-1","price":89.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381513355354,"sku":"BWCS-NK9130MD-2","price":104.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381513388122,"sku":"BWCS-NK9130MD-3","price":115.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-NK9130MD-1.webp?v=1778901340","url":"https:\/\/batteryweb.com\/products\/goldway-6000f-replacement-battery-12v-2300mah-sealed-lead-acid","provider":"BatteryWeb","version":"1.0","type":"link"}