{"product_id":"gp-gp60aaah3bms-replacement-battery-36v-700mah-ni-mh","title":"GP60AAAH3BMS Cordless Phone Replacement Battery 3.6V 700mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eGP GP60AAAH3BMS — 3.6V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 3.6V, 700mAh Ni-MH rechargeable battery for the GP GP60AAAH3BMS cordless phone handset. It fits directly into the handset battery compartment and restores both talk time and standby operation. Use this when the original pack no longer holds a charge and the phone dies shortly after leaving the base.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eGP GP60AAAH3BMS handset fit:\u003c\/strong\u003e\n    This pack matches the 3.6V three-cell NiMH configuration the GP60AAAH3BMS base station charges through its contact pins. Voltage, physical size (44.76 × 30.98 × 10.61mm), and connector orientation all align to the original handset bay.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through charge and discharge on a NiMH-compatible tester. The cells accepted a full charge without voltage reversal, and capacity stabilised at rated output by the fourth cycle.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-charge protocol for NiMH handsets:\u003c\/strong\u003e\n    After installing, seat the handset in its base and leave it for a full 16 hours before first use. NiMH cells shipped in storage-discharged state need this slow initial charge to reach rated capacity — cutting it short locks in a lower ceiling that repeated short charges will not recover.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBase station showing no charge light after fitting a new NiMH pack\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNiMH cells stored for months arrive at a low resting voltage — sometimes below 3.0V across the three cells. Some GP base stations interpret this as an absent or faulty pack and withhold charging current entirely. The fix is to briefly jump-start the cells: remove the battery, let it sit at room temperature for 30 minutes, then reinsert and press the handset firmly onto the base contacts. If the charge light still does not activate, check the contact pins on both the handset and base for corrosion — a clean contact reads above 4.0V from the base within seconds of seating.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eRange drops noticeably mid-call after a battery swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eDECT transmitters pull a short current spike each time the handset communicates with the base. When a NiMH pack is below roughly 3.4V under load, that spike causes a voltage sag the RF circuit cannot absorb, so the handset either drops range or cuts audio briefly. This is most common in the first few charge cycles before the cells are conditioned. Run three to five full charge-and-use cycles and the internal resistance drops enough to stop the sag — check resting voltage after a full charge and confirm it sits at or above 4.1V before testing range again.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43340108955738,"sku":"BWCS-P102CL-1","price":21.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43340108988506,"sku":"BWCS-P102CL-2","price":24.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43340109021274,"sku":"BWCS-P102CL-3","price":26.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-P102CL-1.webp?v=1778367188","url":"https:\/\/batteryweb.com\/products\/gp-gp60aaah3bms-replacement-battery-36v-700mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}