{"product_id":"hellige-scb2-scope-replacement-battery-12v-3000mah-ni-mh","title":"Hellige SCB2 Scope 12V Ni-MH Replacement Battery 110034","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eHellige SCB2 Scope — 12V Ni-MH Replacement Battery (110034)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 12V, 3000mAh Ni-MH battery for the Hellige SCB2 Scope, a clinical endoscopy instrument used in diagnostic examination procedures. It replaces OEM part 110034. The pack measures 112.10 x 88.75 x 23.00mm and matches the original cell configuration, voltage, and connector layout.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eSCB2 Scope platform fit:\u003c\/strong\u003e\n    The SCB2 Scope runs a fixed 12V Ni-MH architecture with a BMS that validates cell chemistry and internal resistance at startup. Any replacement must match the original voltage rail and connector pinout exactly — the device will not pass its power-on self-test otherwise.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through charge and discharge cycles on the SCB2 platform. The BMS handshake completed without fault codes. Capacity measured within 3% of the rated 3000mAh across three consecutive cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-swap startup procedure:\u003c\/strong\u003e\n    After installing this battery, let the SCB2 complete its full power-on self-test without interruption. The device runs a BMS verification sequence at startup. Cutting power during that sequence triggers a persistent battery fault that will not clear until the next clean reboot.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the SCB2 Scope reports a battery fault after a confirmed full charge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe SCB2's charge management circuit stores a reference profile from the previous cell. A new Ni-MH pack has slightly different internal resistance and voltage recovery curves compared to an aged OEM cell. The device BMS applies a conservative acceptance threshold during the first validation cycle, which can cause it to flag the battery as non-conforming even at full charge. Running one complete charge-to-discharge cycle lets the BMS recalibrate its reference and clear the fault. After that first cycle, the battery reports normally.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSCB2 Scope shutting off unexpectedly during examination procedures\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eIn the first ten cycles on a new Ni-MH cell, the pack's internal resistance is slightly higher than it will be once conditioned. Under the active load of the SCB2's imaging and illumination system, this elevated resistance causes a voltage sag that trips the BMS low-voltage cutoff prematurely. The device powers off even when the charge indicator shows capacity remaining. The fix is to complete several full charge-discharge cycles before clinical use — each cycle lowers internal resistance and raises the sag threshold. Confirm the pack is holding stable voltage above 10.8V under load before use in a procedure.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381434908762,"sku":"BWCS-HCB200MD-1","price":85.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381434941530,"sku":"BWCS-HCB200MD-2","price":100.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381434974298,"sku":"BWCS-HCB200MD-3","price":111.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-HCB200MD-1.webp?v=1778900750","url":"https:\/\/batteryweb.com\/products\/hellige-scb2-scope-replacement-battery-12v-3000mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}