{"product_id":"hioki-replacement-battery-74v-2600mah-li-ion","title":"Hioki Z1007 Replacement Battery 7.4V 2600mAh Li-ion","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eHioki Z1007 — 7.4V Li-ion Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 7.4V, 2600mAh (19.24Wh) Li-ion replacement battery for Hioki test and measurement instruments that use the Z1007 pack. It slots into Hioki portable instruments used for electrical diagnostics and field measurement work. Voltage and capacity match the OEM Z1007 specification exactly.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eZ1007 platform fit:\u003c\/strong\u003e\n    Hioki instruments in this family share the Z1007 form factor, connector pinout, and BMS handshake protocol. Swapping to a non-Z1007 pack can trigger a battery fault flag at the instrument's power management layer — this pack avoids that.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran the pack through instrument power-on, probe initialisation, and sustained sensor logging. The BMS held steady through the current spike at probe power-up and did not trip during continuous measurement cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-install calibration cycle:\u003c\/strong\u003e\n    After fitting this battery, run a full calibration cycle through the instrument menu before field deployment. Hioki instruments map battery state during calibration — skipping this step causes premature low-battery warnings during your first measurement session, even with a full charge.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBMS lockout after a Hioki instrument sat unused in a carry case for months\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eLi-ion cells self-discharge during storage. If the pack drops below approximately 2.5V per cell while inside the instrument, the BMS trips a deep-discharge lockout to protect the cells from permanent damage. The instrument will not power on and the charger may show no activity. To recover, connect the pack to the OEM charger and leave it for at least 30–60 minutes — most BMS circuits require a trickle-charge wake signal before resuming normal charge acceptance. If the charger shows no response after 90 minutes, the cells have likely dropped below the BMS recovery threshold of around 2.4V per cell and the pack needs replacement.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eReadings drifting or logging session resetting mid-measurement\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eUnder sustained sensor load, pack voltage can sag enough to cross the instrument's low-voltage reset threshold even when the battery indicator shows capacity remaining. This happens because the indicator reads resting voltage, not load voltage. The gap between the two widens as cells age. If sessions are resetting, check resting voltage with a multimeter — a healthy Z1007 pack at half charge should read above 7.2V at rest. A pack reading below 7.0V at rest under light load is no longer holding adequate headroom for sensor-heavy logging work.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43360782188634,"sku":"BWCS-TOP100XL-1","price":34.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43360782221402,"sku":"BWCS-TOP100XL-2","price":39.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43360782254170,"sku":"BWCS-TOP100XL-3","price":43.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-TOP100XL-1.webp?v=1778616277","url":"https:\/\/batteryweb.com\/products\/hioki-replacement-battery-74v-2600mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}