{"product_id":"hyt-dmr-pd-702-replacement-battery-74v-2600mah-li-ion","title":"HYT BL2006 DMR PD-702 Replacement Battery 7.4V 2600mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eHYT DMR PD-702 \/ PD-782 Series — 7.4V Li-ion Replacement Battery (BL2006)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 7.4V, 2600mAh Li-ion battery for the HYT DMR PD-702, DMR PD-782, PD70X, and PD70XG series digital mobile radios. It replaces OEM part numbers BL2006, BL2006Li, BL2008, BL2503, and BL3001. If your original pack is no longer holding charge across a full shift, this is the direct swap.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003ePD-700 series platform compatibility:\u003c\/strong\u003e\n    The PD-702, PD-782, PD70X, and PD70XG share the same 7.4V battery rail, connector pinout, and BMS handshake protocol — which is why a single pack covers all these models. Swapping between them does not require any firmware or charger change.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through a full charge cycle on a HYT drop-in dock and cycled PTT transmit loads repeatedly. The BMS held steady under the current spike and did not trip into overcurrent protection during sustained transmit bursts.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst insertion into the charger dock:\u003c\/strong\u003e\n    If the dock LED shows a fault on first insertion, remove the pack, wipe the gold contact strip with a dry cloth, and reseat firmly. The HYT platform requires a clean contact cycle to complete the BMS handshake before charging begins — this is not a defective pack.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the PD-702 cuts out mid-transmission on a new BL2006\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eA new Li-ion cell ships at storage voltage — typically 3.6–3.7V per cell, not full charge. When you key up on a fresh-from-box pack, the transmit current spike can pull cell voltage below the BMS cutoff threshold before the pack has been fully charged. The radio interprets this as a low-battery condition and drops TX. Charge the pack fully before first operational use — the dock should show green before you key up for the first time.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBar indicator showing one fewer bar than expected after a full charge cycle\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eHYT radios use a simple voltage-threshold system to drive the bar indicator — each bar corresponds to a voltage band. A new cell that has only completed one charge cycle may rest at a slightly lower open-circuit voltage than a conditioned pack, which shifts the reading down by one bar. Run two full charge-and-use cycles and the resting voltage will stabilise at the correct level. After the second cycle, a full charge should read the same bar count as the original OEM pack — if it still reads low, check that the dock contacts are clean and seating fully against the pack's gold strip.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43303975092314,"sku":"BWCS-HYD788TC-1","price":49.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43303975125082,"sku":"BWCS-HYD788TC-2","price":58.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43303975157850,"sku":"BWCS-HYD788TC-3","price":64.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-HYD788TC_1.webp?v=1777520716","url":"https:\/\/batteryweb.com\/products\/hyt-dmr-pd-702-replacement-battery-74v-2600mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}