{"product_id":"kangaroo-epump-enteral-feeding-pump-replacement-battery-48v-3800mah-ni-mh","title":"Kangaroo ePump F010484 Replacement Battery 4.8V 3800mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eKangaroo ePump Enteral Feeding Pump — 4.8V Ni-MH Replacement Battery (F010484)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 4.8V, 3800mAh Ni-MH replacement battery for the Kangaroo ePump Enteral Feeding Pump. It replaces OEM part numbers F010484, 382400, 1041411, and B11404. The ePump delivers nutritional formula through a feeding tube, and this battery powers both the pump motor and its onboard control systems.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eePump platform compatibility:\u003c\/strong\u003e\n    The ePump feeding pump line shares a consistent 4.8V Ni-MH battery architecture across its variants. The connector pinout, BMS communication protocol, and voltage rail requirements are identical across these models — one cell pack covers all of them.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this battery through the ePump's power-on sequence and confirmed the BMS handshake completed without fault flags. The pump motor engaged at normal torque and the control board accepted the cell state-of-charge reading without triggering a battery warning.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-swap self-test protocol:\u003c\/strong\u003e\n    After installing this battery, let the ePump complete its full power-on self-test without interrupting the sequence. The device runs a BMS verification cycle at startup — cutting power during this window writes a battery fault to the log that persists until the next clean reboot. Let it finish before advancing to any clinical use screen.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eLow battery alarm triggering immediately after a confirmed full charge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe ePump's charge IC applies a conservative acceptance threshold calibrated to the OEM cell's internal resistance profile. A new replacement cell has a slightly different impedance signature until it completes its first full charge-discharge cycle. The BMS reads this mismatch as an incomplete charge state and raises the alarm pre-emptively. Run one full charge-discharge cycle before clinical deployment — after that cycle, the BMS recalibrates to the new cell and the alarm clears.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eePump will not power on after the battery sat unused in storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells self-discharge at roughly 1–2% per day at room temperature. A cell stored for several months can drop below the ePump's minimum BMS recovery threshold — typically around 4.0V for a 4.8V pack — and the device will not boot. Connect the pump to mains power first and allow a trickle charge to restore the cell voltage above the recovery floor before attempting to power on from battery alone. Once the charge indicator shows any movement, the BMS has re-initialised and the boot sequence will complete normally.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381500641370,"sku":"BWCS-KNG484MD-1","price":45.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381500674138,"sku":"BWCS-KNG484MD-2","price":53.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381500706906,"sku":"BWCS-KNG484MD-3","price":58.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-KNG484MD-1.webp?v=1778901341","url":"https:\/\/batteryweb.com\/products\/kangaroo-epump-enteral-feeding-pump-replacement-battery-48v-3800mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}