{"product_id":"karcher-k2-follow-me-replacement-battery-36v-2000mah-li-ion","title":"Kärcher K2 Follow Me 36V Replacement Battery 2000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eKarcher K2 Follow Me — 36V Li-ion Replacement Battery (9.762.930.0)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 36V 2000mAh Li-ion battery replaces the original power pack on the Kärcher K2 Follow Me cordless vacuum cleaner. It fits the handheld unit directly using the original battery slot and connector. Voltage and capacity match OEM spec: 36V, 2000mAh (72Wh).\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eK2 Follow Me platform fit:\u003c\/strong\u003e\n    The K2 Follow Me runs a 36V battery rail with a keyed slide-release housing. This cell matches that rail voltage and uses the same connector geometry and BMS communication protocol the vacuum's motor controller expects at startup.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell on the K2 Follow Me motor assembly and confirmed the BMS handshake completed cleanly at power-on, charge acceptance began immediately on the Kärcher dock, and no overcurrent trips occurred during sustained suction cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging discipline for the K2 Follow Me:\u003c\/strong\u003e\n    Remove the battery from the charging dock once the indicator shows full. The K2 Follow Me dock delivers a low-level trickle after the charge cycle ends — leaving the battery sitting on that trickle accelerates cell degradation faster than normal use cycles.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator reaches low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe K2 Follow Me motor controller pulls higher current when airflow is restricted — a partially blocked filter causes the motor to compensate, drawing well above its rated load. That elevated draw causes voltage to sag at the battery terminals even while the indicator still shows adequate charge. The BMS reads cell voltage directly, not capacity percentage, so the vacuum loses suction power before the LED warns you. Clean or replace the foam and HEPA filters first — if suction recovers immediately, the battery was not the fault.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cutting out mid-session then recovering after a short pause\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a dead battery. When the K2 Follow Me encounters sustained restricted suction — a blockage in the nozzle or a saturated filter — current draw spikes past the BMS protection threshold and the circuit opens to protect the cells. After 30–60 seconds the BMS resets and the motor will start again. Clear the blockage or clean the filter before restarting. If trips continue with clean filters and a fully charged cell, measure resting cell voltage — anything below 32V at rest indicates cell degradation.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43427962912858,"sku":"BWCS-KRK200VX-1","price":150.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43427962945626,"sku":"BWCS-KRK200VX-2","price":178.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43427962978394,"sku":"BWCS-KRK200VX-3","price":199.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-KRK200VX-1.webp?v=1779933587","url":"https:\/\/batteryweb.com\/products\/karcher-k2-follow-me-replacement-battery-36v-2000mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}