{"product_id":"liko-viking-m-replacement-battery-24v-2500mah-ni-mh","title":"Liko Viking M 24V Replacement Battery BAL20001-02","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eLiko Viking M \/ Golvo 8008 Portable Hoist — 24V Ni-MH Replacement Battery (BAL20001-02)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 24V, 2500mAh Ni-MH battery replaces the power cell in the Liko Viking M patient lift and Golvo 8008 Portable Hoist. Both are electric patient-lifting devices used in clinical and home care settings. It matches OEM part numbers BAL20001-02, 2006107, and CSA07033.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eViking M and Golvo 8008 compatibility:\u003c\/strong\u003e\n    Both devices share the same 24V battery bay, connector pinout, and BMS handshake protocol. A single cell spec covers both lifts without modification or adapter.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge, full-load lift cycles, and BMS communication checks. The BMS accepted the cell without fault flags, and the lift completed raise and lower operations through the full stroke.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePower-on self-test after installation:\u003c\/strong\u003e\n    After fitting this battery, allow the Viking M to complete its full power-on self-test without pressing any controls. The device runs a BMS verification sequence at startup — interrupting it causes a persistent false battery fault that will not clear until the next complete reboot.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the Viking M alarms low battery with a freshly charged replacement installed\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe Viking M's charge controller was calibrated against the internal resistance profile of a conditioned OEM cell. A new Ni-MH cell has higher internal resistance until it completes its first full charge-discharge cycle. The BMS reads this elevated resistance as a partially depleted pack and triggers the low battery alarm even when the cell is at full charge. Run one complete charge-to-full followed by a full working cycle before trusting the battery indicator. After that cycle, the BMS recalibrates its threshold to the new cell's profile.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eViking M shuts off mid-lift on the first few uses after battery swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eDuring the first ten cycles, a new Ni-MH cell delivers slightly less instantaneous current under the peak load of a full lift stroke than a conditioned pack. If the voltage sags below the BMS cutoff threshold at peak draw, the lift cuts power mid-operation as a safety measure. This is not a fault — it is the BMS protecting the motor and gearbox from undervoltage. Complete two or three full charge-discharge cycles to condition the cell, and the voltage sag under peak load will drop to within spec. Check that resting voltage reads at least 25.2V before each use during the break-in period.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381426487386,"sku":"BWCS-HRM107MD-1","price":106.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381426520154,"sku":"BWCS-HRM107MD-2","price":125.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381426552922,"sku":"BWCS-HRM107MD-3","price":139.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-HRM107MD-1.webp?v=1778900750","url":"https:\/\/batteryweb.com\/products\/liko-viking-m-replacement-battery-24v-2500mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}