{"product_id":"lux-tools-abs-12-li-replacement-battery-12v-3000mah-li-ion","title":"LUX-TOOLS ABS-12-Li Replacement Battery 12V 3000mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eLUX-TOOLS ABS-12-Li — 12V Li-ion Replacement Battery (3I(NCM)R19\/65)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 12V, 3000mAh Li-ion replacement battery for the LUX-TOOLS ABS-12-Li cordless drill\/driver. It matches the original voltage rail and connector format of the ABS-12-Li platform. When the factory pack degrades and holds less charge, this unit restores full tool function without replacing the drill itself.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eABS-12-Li platform fit:\u003c\/strong\u003e\n    The ABS-12-Li uses a 12V slide-pack format with a specific BMS handshake tied to the charger recognition circuit. This replacement carries the same voltage profile and communication logic, so the charger accepts the pack and the tool's torque control behaves normally.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through repeated motor-start inrush cycles on the ABS-12-Li. The BMS held steady through trigger-pull spikes without nuisance tripping, and cell voltage recovered cleanly between cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBreak-in on the ABS-12-Li:\u003c\/strong\u003e\n    For the first two charge cycles, run the drill at half load — light drilling, low-torque fastening — before moving to full-speed or high-torque work. This lets the BMS map the motor's inrush current draw and set its overcurrent threshold accurately before you hit maximum load.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBMS cutoff on ABS-12-Li motor-start inrush surge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eEvery trigger pull on the ABS-12-Li sends a brief inrush spike to the motor — typically three to five times the steady running current. A BMS that hasn't profiled this tool will sometimes read that spike as a fault and cut output. The 3I(NCM)R19\/65 cell configuration is rated to handle that inrush without tripping, but a cold pack or a freshly installed battery straight from storage may still trigger a momentary cutoff on the first pull. If it cuts out once and then runs normally, that's the BMS calibrating — not a defective unit.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCharger won't recognise the new pack after it's been sitting in storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eLi-ion cells self-discharge during storage. If the pack voltage drops below roughly 9V — the charger's acceptance threshold for a 12V pack — the charger may blink an error or do nothing at all. The fix is a short manual bump: place the battery in the charger, remove it after 30 seconds, and re-seat it firmly. Repeat two or three times. This wakes the BMS and pulls cell voltage just high enough for the charger to begin a normal charge cycle at 12V.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43416031658074,"sku":"BWCS-LTS120PX-1","price":62.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43416031690842,"sku":"BWCS-LTS120PX-2","price":73.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43416031723610,"sku":"BWCS-LTS120PX-3","price":82.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-LTS120PX-1.webp?v=1779759610","url":"https:\/\/batteryweb.com\/products\/lux-tools-abs-12-li-replacement-battery-12v-3000mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}