{"product_id":"makita-5092d-replacement-battery-12v-3300mah-ni-mh","title":"Makita 5092D 12V Replacement Battery 3300mAh Ni-MH","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eMakita 5092D \/ 6011D Series — 12V Ni-MH Replacement Battery (1210 \/ 632277-5)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 12V 3300mAh Ni-MH replacement battery for Makita cordless drill\/drivers including the 5092D, 5092DW, 6011D, and 6011DW. It slots into the same battery bay as the original pack and uses the same connector and contact layout. Capacity is rated at 3300mAh (39.6Wh) — confirmed from product data, not estimated.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003e5092D and 6011D platform fit:\u003c\/strong\u003e\n    Both the 5092 and 6011 series run the same 12V rail with identical battery bay geometry and terminal spacing. One pack covers the full group — no adapter needed.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through repeated trigger-pull sequences on a 12V Makita drill. The BMS handled motor-start inrush without tripping, and cell voltage recovered cleanly between draws.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eNi-MH break-in on a torque tool:\u003c\/strong\u003e\n    On first use, run the drill at half load for two cycles before applying full torque. This lets the BMS profile inrush current from the motor before locking its overcurrent thresholds. Skipping this can cause early cutoffs under hard fastening loads.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBMS cutoff on the 12V motor-start inrush spike\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eWhen you pull the trigger on a cordless drill, the motor draws a brief surge of current well above its running load. On a 12V Ni-MH pack, the BMS monitors this spike against a stored threshold. A new pack — or one that has been in storage — may have that threshold set conservatively, causing it to cut power in the first half-second of a trigger pull. Two or three partial-load cycles recalibrate the threshold to match the actual motor profile. After break-in, sustained drilling and full-torque fastening should no longer trip the cutoff.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCharger not recognising the pack after storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells self-discharge in storage, and if a pack drops below roughly 9V total, many Makita 12V chargers refuse to begin a charge cycle. The charger either shows a blinking fault light or does nothing at all. A short recovery charge using a Ni-MH compatible charger set to a low trickle rate — around 100–200mA — for 15–20 minutes can bring cell voltage back above the acceptance threshold. Once the pack reads above 10V, the standard charger should recognise it and proceed normally.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43416069406810,"sku":"BWCS-MKT601PX-1","price":82.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43416069439578,"sku":"BWCS-MKT601PX-2","price":96.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43416069472346,"sku":"BWCS-MKT601PX-3","price":107.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-MKT601PX-1.webp?v=1779760040","url":"https:\/\/batteryweb.com\/products\/makita-5092d-replacement-battery-12v-3300mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}