{"product_id":"medical-industries-vacumax-605-aspirator-replacement-battery-12v-1800mah-ni-mh","title":"Medical Industries VACUMAX 605 Replacement Battery 12V 1800mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eMedical Industries VACUMAX 605 Aspirator — 12V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 12V 1800mAh Ni-MH battery for the Medical Industries VACUMAX 605 portable aspirator. It fits the handheld suction unit used for fluid and secretion removal during clinical procedures. Voltage, capacity, and connector match the original cell configuration.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eVACUMAX 605 fit:\u003c\/strong\u003e\n    The 605 aspirator runs a 12V Ni-MH rail with a specific connector orientation and BMS handshake tied to cell chemistry. Swapping to a different chemistry — even at the same voltage — trips a chemistry mismatch fault in the charge controller. This cell matches the original Ni-MH profile the device expects.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through the VACUMAX 605 charge controller and monitored BMS response under suction-motor load. The protection circuit held voltage within spec across load spikes, and the charge IC accepted the cell without flagging a fault code on the first cycle.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-swap self-test protocol:\u003c\/strong\u003e\n    After installing this battery, let the VACUMAX 605 complete its full power-on self-test without interruption. The device runs a BMS verification sequence at startup — cutting power mid-sequence locks in a false battery fault that persists until the next clean reboot.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the VACUMAX 605 alarms low battery immediately after a confirmed full charge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe VACUMAX 605 charge controller stores a chemistry and capacity baseline from the previous cell. When a new cell is installed, the BMS compares its first-cycle discharge curve against that stored profile. A fresh Ni-MH cell behaves differently in the first few cycles — lower initial capacity, steeper voltage drop under load — which the controller reads as a degraded battery. Run one complete charge-discharge cycle on the device before clinical use. After that cycle, the BMS recalibrates its threshold to the new cell's actual curve and the alarm clears.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eVACUMAX 605 will not power on after the battery has been in storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eNi-MH cells self-discharge during storage, and a cell that has sat unused can drop below the BMS recovery threshold — typically around 9V for a 12V pack. When voltage falls that low, the protection circuit blocks output to prevent cell damage, and the device shows no response at all. Connect the battery to the VACUMAX 605 charger and leave it for a full charge cycle without interrupting. The charge IC on this device applies a trickle pre-charge at voltages below 10.5V to recover the cell before switching to normal charge current.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381467775066,"sku":"BWCS-CBP308MD-1","price":105.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381467807834,"sku":"BWCS-CBP308MD-2","price":121.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381467840602,"sku":"BWCS-CBP308MD-3","price":133.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-CBP308MD_1.webp?v=1778901051","url":"https:\/\/batteryweb.com\/products\/medical-industries-vacumax-605-aspirator-replacement-battery-12v-1800mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}