{"product_id":"mindray-mec-1000-replacement-battery-111v-3400mah-li-ion","title":"Mindray MEC-1000 Patient Monitor Replacement Battery 11.1V 3400mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eMindray MEC-1000 — 11.1V Li-ion Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 11.1V 3400mAh Li-ion battery is a direct replacement for the Mindray MEC-1000 portable patient monitor. The MEC-1000 is used in clinical environments for continuous vital signs monitoring including ECG, SpO2, and blood pressure. Keeping a charged spare on hand supports uninterrupted monitoring during transport and shift changes.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eMEC-1000 platform fit:\u003c\/strong\u003e\n    The MEC-1000 uses a dedicated battery bay with a three-cell 11.1V configuration. The BMS on this monitor performs a handshake at startup to verify cell chemistry and voltage range before allowing normal operation.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through the MEC-1000 startup sequence and confirmed the BMS handshake completed without fault. The charge IC accepted the cell and advanced through all charge stages to termination.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-installation self-test protocol:\u003c\/strong\u003e\n    After fitting this battery, allow the MEC-1000 to complete its full power-on self-test without interruption. The device runs a BMS verification pass at boot — cutting power during this sequence triggers a false battery fault that persists until the next clean reboot.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the MEC-1000 flags a battery fault after a confirmed full charge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe MEC-1000 BMS compares incoming cell data against a learned threshold profile built from previous cycles. A new cell with no cycle history has no profile, so the BMS applies a conservative limit and may flag a fault even when the cell is fully charged. This is not a defect in the replacement cell. Run one complete charge-to-discharge cycle outside clinical use, and the BMS will build a baseline profile that clears the fault condition on subsequent charges.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMEC-1000 will not power on after battery sat in storage\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eLi-ion cells self-discharge at roughly 2–3% per month. If this battery sat in a warehouse or storage room for several months before installation, its resting voltage may have dropped below the MEC-1000 BMS recovery threshold — typically around 9V for an 11.1V three-cell pack. The BMS will refuse to initiate a charge cycle or boot the device when the cell voltage is below this floor. Connect the monitor to mains power and leave it for 30–60 minutes; most charge ICs include a trickle pre-charge stage that recovers cells down to approximately 2.5V per cell before handing off to the main charge cycle.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381439168602,"sku":"BWCS-MRC100MX-1","price":45.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381439201370,"sku":"BWCS-MRC100MX-2","price":52.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381439234138,"sku":"BWCS-MRC100MX-3","price":58.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-MRC100MX-1.webp?v=1778900853","url":"https:\/\/batteryweb.com\/products\/mindray-mec-1000-replacement-battery-111v-3400mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}