{"product_id":"moneual-p10-replacement-battery-144v-2600mah-li-ion","title":"Moneual P10 Robotic Vacuum Replacement Battery 14.4V 2600mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eMoneual P10 — 14.4V Li-ion Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 14.4V Li-ion battery rated at 2600mAh (37.44Wh), built as a direct replacement for the Moneual P10 robotic vacuum cleaner. It slots into the P10's battery bay and powers the drive motors, suction motor, and navigation electronics. Voltage and capacity match the original specification exactly.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eP10 platform fit:\u003c\/strong\u003e\n    The P10 runs a 14.4V power rail across its suction and drive systems from a single battery pack. This cell matches that rail. The BMS on the P10 monitors cell voltage during discharge and will cut power if the pack voltage drops below threshold — a cell that cannot hold 14.4V under load will trigger that cutoff early.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this battery through full charge and discharge runs on a P10 unit. The BMS handshake completed without fault codes, and the pack held voltage through both suction and drive load simultaneously. No mid-cycle cutoffs were recorded.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging behaviour on the P10:\u003c\/strong\u003e\n    Remove the P10 from its charging dock once the battery reaches full charge. The P10 dock does not switch to a true standby mode — it continues pushing a trickle current into the pack. Li-ion cells sitting under continuous low-level charge lose capacity faster than cells that are charged fully and then left off the dock.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator shows low on the P10\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a voltage sag problem, not a capacity problem. When the suction motor hits a restriction — a blocked filter, packed dustbin, or dense carpet — it draws more current than rated. A battery with degraded cells cannot hold 14.4V under that spike. Voltage sags, the suction motor loses power, and the indicator reads mid-charge because the pack still has capacity in reserve. Cleaning or replacing the filter is the first step. If sag persists on a clear filter with a fresh battery, check that resting voltage after a full charge reads at least 16.2V before the first run.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cuts out mid-clean then recovers after a few seconds\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip. The P10's battery management system shuts down output when current draw exceeds a set threshold, then resets once the pack temperature or load drops. It usually happens when the suction path is partially blocked — the motor fights harder, pulls more amps, and trips the BMS. The recovery pause is the BMS resetting, not a loose connection. Clear the filter and brush roll first. If trips continue on a clean machine with a new battery, the suction motor itself may be drawing above spec.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43427992141914,"sku":"BWCS-PMR877VX-1","price":39.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43427992174682,"sku":"BWCS-PMR877VX-2","price":46.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43427992207450,"sku":"BWCS-PMR877VX-3","price":51.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-PMR877VX-1.webp?v=1779933755","url":"https:\/\/batteryweb.com\/products\/moneual-p10-replacement-battery-144v-2600mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}