{"product_id":"neusoft-nsc-m10-replacement-battery-108v-5200mah-li-ion","title":"Neusoft NSC-M10 10.8V Replacement Battery 5200mAh Li-ion","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eNeusoft NSC-M10 — 10.8V Li-ion Replacement Battery (INR18650 3S2P)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 10.8V, 5200mAh (56.16Wh) lithium-ion battery pack built in a 3S2P INR18650 configuration. It fits the Neusoft NSC-M10 portable medical device. The cell arrangement matches the voltage rail and BMS handshake required by the NSC-M10's power management circuit.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eNSC-M10 platform fit:\u003c\/strong\u003e\n    The 3S2P topology delivers a 10.8V nominal rail across two parallel cell strings, matching the NSC-M10's charge IC input range. The BMS handles cell balancing across all six INR18650 cells, which is what the device expects during its power-on verification sequence.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through charge and load cycles on the bench. The BMS maintained cell balance within tolerance and responded correctly to both charge termination and low-voltage cutoff signals — no fault flags during the test sequence.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-installation self-test protocol:\u003c\/strong\u003e\n    After fitting this battery, allow the NSC-M10 to complete its full power-on self-test without interruption. The device runs a BMS verification step at startup — cutting power mid-sequence stores a false battery fault that persists until the next clean reboot cycle.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eDevice not completing boot sequence on new battery\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe NSC-M10 runs a multi-step BMS verification during boot that checks cell voltage thresholds before allowing the device to reach the operating state. A new pack that has partially self-discharged during shipping may present a resting voltage below the boot threshold, causing the sequence to stall or abort. This is not a failed battery — it is the device rejecting a pack it has not yet verified. Connect to mains power and allow a full charge cycle to complete before attempting to power the device on battery alone.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCharge indicator not reaching 100% on first charge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe NSC-M10's charge IC applies a conservative current limit when it encounters a cell pack it has not previously profiled. On the first charge cycle, the termination voltage may be set slightly below the full 12.6V end-of-charge threshold, causing the indicator to plateau at 90–95%. This is a one-cycle behaviour tied to the charge IC's new-cell conditioning logic. Run one complete charge-discharge cycle and the IC will recalibrate its termination point — the indicator should reach 100% on the second charge.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381429207130,"sku":"BWCS-NSM100MD-1","price":65.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381429239898,"sku":"BWCS-NSM100MD-2","price":76.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381429272666,"sku":"BWCS-NSM100MD-3","price":85.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-NSM100MD-1.webp?v=1778900788","url":"https:\/\/batteryweb.com\/products\/neusoft-nsc-m10-replacement-battery-108v-5200mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}