{"product_id":"orgapack-or-t650-replacement-battery-36v-4000mah-li-ion","title":"Orgapack OR-T650 Replacement Battery 36V 4000mAh Li-ion","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eOrgapack OR-T650 — 36V Li-ion Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 36V 4000mAh Li-ion battery replaces the original pack in the Orgapack OR-T650 electric strapping tool. The OR-T650 is a portable battery-powered strapper used in logistics, warehousing, and packaging lines to tension and seal plastic or steel strapping tape. Voltage and capacity match the original specification exactly.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eOR-T650 platform fit:\u003c\/strong\u003e\n    The OR-T650 runs a 36V motor circuit with a BMS handshake that monitors cell voltage under tensioning load. This pack uses the same cell configuration and connector pinout, so the tool's onboard electronics recognise it without recalibration.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through full tensioning cycles on the OR-T650, monitoring BMS response at peak motor draw. The pack held stable voltage through the tension-and-weld sequence without triggering low-voltage cutoff.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eCold warehouse use:\u003c\/strong\u003e\n    If the tool operates in a refrigerated or unheated warehouse, bring the battery above 10°C before the first tensioning cycle. Cold cells have higher internal resistance — the OR-T650 motor draws a sharp current spike at maximum tension, and a cold pack below that threshold will trip the BMS mid-cycle.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eBMS cutoff during the tensioning cycle on the OR-T650\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe OR-T650 motor peaks sharply at maximum strap tension — this is the highest single current draw in the tool's operating sequence. If the battery's BMS detects cell voltage drop below its cutoff threshold at that moment, it shuts the pack down instantly. This is not a tool fault; it is the BMS protecting the cells from over-discharge under surge load. A fully charged pack above 36V nominal should clear this threshold through the tensioning cycle without cutoff.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCharger fault light on a new pack after the tool has been stored unused\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eLi-ion cells discharge slowly in storage, and if a pack sits long enough, cell voltage drops below the charger's acceptance threshold — typically around 2.5V per cell. The charger sees a voltage it does not recognise as safe to charge and throws a fault instead of starting a charge cycle. To recover the pack, check that the charger contacts are clean and seated firmly, then hold the pack on charge for up to 10 minutes — many chargers will re-attempt acceptance once the cells tick above 2.8V per cell. If the fault persists past that point, the pack has self-discharged past recovery.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43416244519002,"sku":"BWCS-FRM311PW-1","price":160.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43416244551770,"sku":"BWCS-FRM311PW-2","price":189.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43416244584538,"sku":"BWCS-FRM311PW-3","price":211.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-FRM311PW-1.webp?v=1779761098","url":"https:\/\/batteryweb.com\/products\/orgapack-or-t650-replacement-battery-36v-4000mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}