{"product_id":"philips-suresigns-v24e-replacement-battery-108v-7800mah-li-ion","title":"Philips SureSigns V24E ME202C Replacement Battery 10.8V","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003ePhilips SureSigns V24E \/ VS2 \/ VS3 — 10.8V Li-ion Replacement Battery (ME202C)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 10.8V, 7800mAh lithium-ion battery built to the ME202C specification. It fits the Philips SureSigns V24E, VS2, and VS3 portable patient monitors. These monitors are used in clinical transport and bedside assessments where a failed battery is not a minor inconvenience.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eSureSigns V24E, VS2, and VS3 compatibility:\u003c\/strong\u003e\n    All three models share the same 10.8V battery bus, ME202C connector pinout, and BMS handshake protocol. A single cell fits all three without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran the ME202C replacement through charge and discharge cycles on a SureSigns VS2. The BMS accepted the cell, completed status reporting, and held voltage within spec under simulated monitoring load.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePower-on self-test after installation:\u003c\/strong\u003e\n    After inserting this battery, let the device complete its full startup self-test without interruption. The SureSigns BMS runs a verification sequence at boot. Cutting power during this cycle registers a false battery fault that persists until the next clean reboot.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the SureSigns VS3 reports a battery fault after a confirmed full charge\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe VS3 BMS stores a learned capacity profile from the previous cell. When a new cell is installed, the controller compares measured internal resistance and charge curve against that stored profile. A fresh lithium-ion cell has slightly higher initial resistance than a conditioned cell, so the BMS flags a mismatch. This is not a defect. Run one full charge-discharge cycle and the BMS rewrites the profile to match the new cell.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCharge indicator stuck below 100% on first charge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eOn the first charge, the SureSigns charge IC applies a conservative current limit to an unrecognised cell. This causes the charge cycle to terminate early, leaving the indicator at 85–95%. The cell is not faulty — the charge IC has not yet mapped the full capacity of the new pack. Discharge the battery fully through normal monitor use, then run a complete charge cycle uninterrupted. After that second cycle, the indicator reads correctly at 100%.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43306857988186,"sku":"BWCS-PHV200MD-1","price":511.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43306858020954,"sku":"BWCS-PHV200MD-2","price":611.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43306858053722,"sku":"BWCS-PHV200MD-3","price":686.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-PHV200MD_1.webp?v=1777768792","url":"https:\/\/batteryweb.com\/products\/philips-suresigns-v24e-replacement-battery-108v-7800mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}