{"product_id":"philips-trnsbv1-range-replacement-battery-37v-1800mah-li-ion","title":"Philips TRNSBV1 Medical Device Replacement Battery 3.7V 1800mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003ePhilips TRNSBV1 Range — 3.7V Li-ion Replacement Battery (453564107861)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 3.7V, 1800mAh Li-ion cell replaces OEM part 453564107861 in the Philips TRNSBV1 Range and SRR measurements devices. These are portable clinical and home healthcare units — patient monitoring and diagnostic equipment that depends on a stable, rechargeable power source. Voltage and capacity match the original spec exactly.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eTRNSBV1 Range and SRR compatibility:\u003c\/strong\u003e\n    Both device lines share the same 3.7V power rail, connector footprint, and BMS handshake protocol — one cell fits the full cluster. The OEM part number 453564107861 covers this group because the BMS threshold and charge profile are identical across models.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through charge, standby, and active draw states on the TRNSBV1 platform. The BMS accepted the cell without fault flags, passed its verification handshake, and held the expected voltage curve from full charge down to the low-battery cutoff threshold.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003ePost-installation self-test protocol:\u003c\/strong\u003e\n    After installing this cell, let the device complete its full power-on self-test without interruption. Medical device BMS firmware runs a startup verification sequence — cutting power during that window creates a false battery fault that persists until the next clean reboot.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eDevice not completing boot sequence after battery swap\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThe TRNSBV1's BMS runs a learn cycle on first use — it checks cell voltage, internal resistance, and charge state before allowing the boot sequence to complete. A new cell straight from packaging may sit slightly below the BMS acceptance threshold after transit self-discharge. If the device stalls at startup, charge the cell fully before the first use, then reboot. One complete charge-discharge cycle is usually enough for the BMS to register the cell as verified and pass the boot gate.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eLow battery alarm triggers immediately after a confirmed full charge\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens when the BMS compares the new cell's charge profile against stored OEM baseline values and flags a mismatch — not an actual low charge. The alarm threshold is calibrated to OEM cell chemistry, and a fresh replacement cell needs one full charge-discharge cycle before the BMS recalibrates its reference. Run one complete cycle: charge to 100%, allow normal discharge during use, then recharge fully. After that cycle, the alarm threshold re-anchors to the actual cell and false triggers stop.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43381447000154,"sku":"BWCS-PHR100MD-1","price":38.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43381447032922,"sku":"BWCS-PHR100MD-2","price":44.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43381447065690,"sku":"BWCS-PHR100MD-3","price":48.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-PHR100MD-1.webp?v=1778900958","url":"https:\/\/batteryweb.com\/products\/philips-trnsbv1-range-replacement-battery-37v-1800mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}