{"product_id":"pidion-bp30-replacement-battery-37v-3900mah-li-polymer","title":"Pidion BP30 Barcode Scanner Replacement Battery 3.7V 3900mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003ePidion BP30 — 3.7V Li-Polymer Replacement Battery (BAT-BP30-45)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 3.7V 3900mAh Li-Polymer battery replaces the OEM pack in the Pidion BP30 handheld barcode scanner. It fits the BP30 used in retail, warehouse, and inventory operations. Capacity is 14.43Wh — matched to the original cell specification.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eBP30 platform fit:\u003c\/strong\u003e\n    The BP30 runs a single-cell 3.7V Li-Polymer architecture with a dedicated BMS that monitors cell voltage and temperature on each scan trigger pull. This pack matches that voltage rail and connector pinout exactly, so the scanner's firmware recognises the pack and reports state of charge correctly.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this pack through repeated scan-burst sequences and monitored the BMS response at low state of charge. The protection circuit held cutoff cleanly at the expected minimum cell voltage without nuisance trips during trigger inrush.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-shift preparation:\u003c\/strong\u003e\n    After installing, place the BP30 in its cradle for a full charge cycle before starting a pick-and-pack shift. Scan trigger inrush current is highest when the cell is near minimum — a fully charged pack prevents false BMS trips during the first hour of use.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCradle showing a charging error on a brand-new pack\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eA new Li-Polymer pack ships at a storage charge — typically around 3.6–3.65V per cell — not at full voltage. Some BP30 cradles interpret this low starting voltage as a fault condition and flag a charging error on the dock LED. This is a dock-side detection issue, not a defective battery. Remove the pack, wipe the gold contact pads on both the battery and the cradle slot with a dry cloth, then reseat firmly. The cradle should re-initialise the charge cycle within 30 seconds of a clean contact.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eScanner losing wireless connection during rapid scan bursts\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eDuring a rapid scan burst, the BP30 draws current simultaneously from the imager, the processor, and the wireless radio. On a degraded or deeply discharged pack, that combined inrush pulls cell voltage below the radio module's minimum operating threshold — the radio drops out first because it is lower priority than the scan engine. The BMS may not trip, so the scanner appears functional but loses its network session. Charge the pack to full before the shift and check that cell voltage under load stays above 3.5V — if it sags below that point, the pack has lost usable capacity and needs replacement.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43324769992794,"sku":"BWCS-BUP300BL-1","price":43.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43324770025562,"sku":"BWCS-BUP300BL-2","price":50.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43324770058330,"sku":"BWCS-BUP300BL-3","price":55.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-BUP300BL_1.webp?v=1778123055","url":"https:\/\/batteryweb.com\/products\/pidion-bp30-replacement-battery-37v-3900mah-li-polymer","provider":"BatteryWeb","version":"1.0","type":"link"}