{"product_id":"redmibook-redmibook-13-replacement-battery-77v-5200mah-li-polymer","title":"RedmiBook 13 R13B03W Compatible Battery 7.7V 5200mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eRedmiBook 13 — 7.7V Li-Polymer Replacement Battery (R13B03W)\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 7.7V, 5200mAh (40.04Wh) Li-Polymer replacement battery for the RedmiBook 13 notebook computer. It fits the R13B03W cell slot directly. Capacity figures are taken from product data, not estimated from third-party sources.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eRedmiBook 13 platform fit:\u003c\/strong\u003e\n    The R13B03W uses a specific connector pinout and BMS handshake tied to the RedmiBook 13 motherboard. Voltage rails on this platform are tuned to 7.7V — cells rated at 7.4V or 7.6V will trigger an incompatibility warning in MIUI's power management layer.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this cell through charge and discharge cycles on a RedmiBook 13 unit. The BMS accepted the cell without fault codes, and the charge controller stepped through each charge phase — pre-charge, CC, and CV — without interruption.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eFirst-cycle calibration on this model:\u003c\/strong\u003e\n    After fitting, discharge the laptop fully until it hibernates on its own, then charge in one uninterrupted session to 100%. This resets the BIOS battery learn cycle and clears the inaccurate health warning the firmware throws after every cell swap on this model.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eWhy the RedmiBook 13 reports poor battery health immediately after a cell swap\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe RedmiBook 13 stores battery health data in EEPROM on the old cell. When a new cell goes in, the BIOS reads stale or blank EEPROM values and flags the battery as degraded or unknown. This is a firmware read issue, not a fault with the replacement cell. Running one full discharge-to-hibernate followed by a full charge gives the BIOS enough data to rewrite accurate health figures. After two or three cycles, the health warning clears on its own.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eRedmiBook 13 shutting down at 20–30% charge shown on screen\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens when the fuel gauge IC has not yet calibrated against the new cell's voltage curve. The OS reports 20–30% remaining, but the cell voltage has already dropped below the cutoff threshold under CPU and display load. The system shuts down to protect the cell, even though the percentage looks fine. Run two full discharge-to-hibernate cycles and charge each time to 100% — after that, the fuel gauge IC maps the new cell accurately and the early shutdowns stop.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43409531240538,"sku":"BWCS-XMR133NB-1","price":66.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43409531273306,"sku":"BWCS-XMR133NB-2","price":78.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43409531306074,"sku":"BWCS-XMR133NB-3","price":87.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-XMR133NB_1.webp?v=1779579941","url":"https:\/\/batteryweb.com\/products\/redmibook-redmibook-13-replacement-battery-77v-5200mah-li-polymer","provider":"BatteryWeb","version":"1.0","type":"link"}