{"product_id":"reed-r2050-replacement-battery-37v-3400mah-li-ion","title":"Reed R2050 Thermal Camera Replacement Battery 3.7V 3400mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eReed R2050 Thermal Imaging Camera — 3.7V Li-ion Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis 3.7V 3400mAh Li-ion battery replaces the internal cell in the Reed R2050 thermal imaging camera. It fits the R2050 used in building diagnostics, electrical panel inspections, and HVAC surveys. Voltage and capacity match the original cell — no modifications needed to install.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eR2050 platform fit:\u003c\/strong\u003e\n    The R2050 runs its infrared detector and LCD display off a single 3.7V Li-ion cell. Both loads share the same voltage rail. Any replacement must hold stable output across the full discharge curve — voltage sag mid-inspection causes the detector to lose calibration lock before the battery indicator reaches low.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell under simultaneous display and detector load. The BMS held cutoff at 2.75V and did not trip under the combined draw. Capacity measured within 3% of the rated 3400mAh across three discharge cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDetector warm-up after battery swap:\u003c\/strong\u003e\n    After fitting a new cell, power on the R2050 and wait 60 seconds before starting measurements. The thermal detector needs the internal electronics to stabilise for accurate baseline calibration. Starting an inspection immediately after cold power-on will produce shifted temperature readings until the detector self-corrects.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eThermal accuracy dropping before the battery indicator reads low\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe R2050's infrared detector is voltage-sensitive. As the cell discharges past roughly 3.5V, detector bias current becomes inconsistent — temperature readings drift by several degrees before the camera reports any battery warning. This is not a firmware fault. It is a hardware characteristic of uncooled microbolometer detectors running close to their minimum supply voltage. If readings look unstable but the battery icon still shows charge, check actual cell voltage with a multimeter. Below 3.5V under load, swap the battery.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eR2050 shutting down mid-inspection on a battery that was fully charged\u003c\/h3\u003e\n\n  \u003cp class=\"bpw-desc-p\"\u003eThe R2050 draws current from two sources at once — the display backlight and the detector heating element. That combined load spikes when the camera processes high-contrast thermal scenes. If the BMS interprets a brief voltage dip as an undervoltage fault, it cuts power immediately. A degraded or counterfeit cell with high internal resistance will trigger this at apparent states of charge above 50%. Replace the cell and confirm the new battery rests at 4.1–4.2V fully charged before fitting it.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43426120990810,"sku":"BWCS-EXT7XL-1","price":26.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43426121023578,"sku":"BWCS-EXT7XL-2","price":30.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43426121056346,"sku":"BWCS-EXT7XL-3","price":33.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-EXT7XL_1.webp?v=1779930364","url":"https:\/\/batteryweb.com\/products\/reed-r2050-replacement-battery-37v-3400mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}