{"product_id":"ricambi-robot-aspiratore-imetec-replacement-battery-12v-800mah-ni-mh","title":"Ricambi Robot Aspiratore Imetec 12V Ni-MH Replacement Battery","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eRicambi Robot Aspiratore Imetec — 12V Ni-MH Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 12V 800mAh Ni-MH replacement battery for the Imetec Robot Aspiratore robotic vacuum cleaner. It slots into the vacuum's battery bay and powers the motor and navigation electronics. Use the Capacity figure above — 800mAh — as the reference spec for this cell.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eImetec Robot Aspiratore fit:\u003c\/strong\u003e\n    The Imetec robotic vacuum runs a 12V rail to drive both the brush motor and the onboard navigation logic. This cell matches that voltage and the physical bay dimensions — 70.50 × 49.30 × 28.50mm — so the connector seats without modification.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We cycled this cell through charge and discharge on a 12V Ni-MH circuit. The BMS held cutoff correctly at low voltage and the cell reached rated capacity within three full cycles.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging on Ni-MH cells:\u003c\/strong\u003e\n    Do not leave the robot sitting on the dock permanently. Ni-MH cells degrade faster under continuous trickle charge than under normal charge-and-remove cycles. Charge to full, then lift the unit off the dock.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eSuction dropping before the battery indicator reaches low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens when the motor draws more current than the cell can sustain at that state of charge. A partially blocked filter increases motor load sharply — even a moderate blockage can push draw above the cell's continuous output rating. The voltage sags under that load before the indicator circuit registers a low-battery condition. Clear the filter first, then check whether suction holds across a full cleaning run.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cutting out mid-cycle and then recovering after a pause\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a dead battery. When suction is restricted — blocked filter, tangled brush roll, or a piece of debris lodged at the inlet — the motor labours and current spikes past the BMS threshold. The BMS cuts the circuit to protect the cell, the robot stops, and after a short thermal recovery the BMS resets and the unit starts again. Fix the restriction before assuming the battery is at fault. If the trip repeats on a clear filter, measure pack voltage under load — it should hold above 10.8V during normal operation.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43428062494810,"sku":"BWCS-EDC110VX-1","price":37.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43428062527578,"sku":"BWCS-EDC110VX-2","price":43.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43428062560346,"sku":"BWCS-EDC110VX-3","price":47.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-EDC110VX-1.webp?v=1779934014","url":"https:\/\/batteryweb.com\/products\/ricambi-robot-aspiratore-imetec-replacement-battery-12v-800mah-ni-mh","provider":"BatteryWeb","version":"1.0","type":"link"}