{"product_id":"robojet-x-force-replacement-battery-144v-5200mah-li-ion","title":"RoboJet X-Force 14.4V Cordless Vacuum Replacement Battery 5200mAh","description":"\u003cdiv class=\"bpw-desc\"\u003e\n  \u003ch2 class=\"bpw-desc-h2\"\u003eRoboJet X-Force — 14.4V Li-ion Replacement Battery\u003c\/h2\u003e\n\n  \u003cp class=\"bpw-desc-lead\"\u003eThis is a 14.4V, 5200mAh (74.88Wh) lithium-ion battery pack for the RoboJet X-Force cordless vacuum. It fits the handheld and stick configurations of the X-Force platform. When the original cell degrades and runtime shortens noticeably, this pack restores full operating capacity.\u003c\/p\u003e\n\n  \u003cul class=\"bpw-desc-bullets\"\u003e\n    \u003cli\u003e\n\u003cstrong\u003eX-Force platform fit:\u003c\/strong\u003e\n    The X-Force motor rail runs at 14.4V nominal. The BMS in this pack is matched to that voltage window, so the vacuum's power management reads charge state correctly and does not trigger a false low-battery cutoff early in the cycle.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eBench tested on actual hardware:\u003c\/strong\u003e\n    We ran this pack through full charge and discharge cycles on the X-Force motor assembly. The BMS held the overcurrent threshold steady under sustained suction load, and charge termination occurred cleanly without overrun.\u003c\/li\u003e\n\n    \u003cli\u003e\n\u003cstrong\u003eDock charging habit for the X-Force:\u003c\/strong\u003e\n    Do not leave the X-Force sitting on its charging dock permanently. Continuous trickle charge degrades cell capacity faster than normal cycling. Charge to full, then remove the vacuum from the dock until the next use.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\n  \u003chr class=\"bpw-desc-divider\"\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eCordless vacuum losing suction before the battery indicator reaches low\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis happens when the motor draws more current than the BMS expects, usually because a partially blocked filter forces the motor to work harder. The BMS sees elevated current draw and pulls back voltage to the motor before the cell is actually depleted. The indicator still shows charge remaining because the cell voltage is fine — it is the current draw triggering the sag. Clean the filter first, then retest; suction should stay consistent through the full charge cycle.\u003c\/p\u003e\n\n  \u003ch3 class=\"bpw-desc-h3\"\u003eMotor cuts out mid-clean then recovers after a few seconds\u003c\/h3\u003e\n  \u003cp class=\"bpw-desc-p\"\u003eThis is a BMS overcurrent trip, not a faulty battery. When the vacuum picks up a blockage or the filter is restricted, motor current spikes sharply. The BMS trips to protect the cells, cutting power for a few seconds before resetting. It will keep happening on the same run if the restriction is still present. Clear the blockage, check the filter is seated correctly, and confirm the pack voltage reads above 13V before the next cycle.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"BatteryWeb","offers":[{"title":"Warranty 1 Year","offer_id":43427996336218,"sku":"BWCS-PCM710VX-1","price":70.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 2 Year","offer_id":43427996368986,"sku":"BWCS-PCM710VX-2","price":83.99,"currency_code":"USD","in_stock":true},{"title":"Warranty 3 Year","offer_id":43427996401754,"sku":"BWCS-PCM710VX-3","price":92.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0674\/4775\/0746\/files\/BW-CS-PCM710VX-1.webp?v=1779933755","url":"https:\/\/batteryweb.com\/products\/robojet-x-force-replacement-battery-144v-5200mah-li-ion","provider":"BatteryWeb","version":"1.0","type":"link"}